Introduction. Femur neck fractures (NOF) in the young could result in mal-union, non-union and avascular necrosis of the femoral head. Osteosynthesis is the standard of management in NOFs in young patient above complications sometimes end in Arthroplasty. The aim of our study is to identify predictors of NOF failures in the young population. Method. A retrospective study conducted in a single center. Patients with NOF fractures below the age of <50y excluding pathological and osteoporotic fractures were assessed in the period from 2005–2008. The mean follow-up was 22 months (6–40). Fractures were classified according to Gardens classification. Our Aim was to identify causative factors for fixation failures. Analysis was done using SPSS 17.0. Results. Within the 4 year period we identified 41 NOF fractures, 24 (75%) fractures were displaced. 7 (25%) out of the displaced fractures went in to failure and required arthroplasty. 3 (42%) went in to avascular necrosis and 2(28.5%) went in to screw cut out and non unions. All failures were primarily fixed with cancellous screws. We identified Male sex (p=0.03), Pre-operative delay of >25h (p=0.04), Chronic alcohol intake (p=0.02) and intra operative time >107min (p=0.001) as the main predictors of NOF failures in the young. Conclusion. Early surgical intervention within 25h, restricting the operation time to less than 107min would reduce the failure rates. We would recommend arthroplasty for patients who are chronic alcoholics

Introduction. Even in localized collapse due to osteonecrosis of the femoral head, a femoral head can be preserved by rotational osteotomy. In addition to anterior rotation, originally described by Sugioka, much more correction can be obtained by posterior rotation. But, transtrochanteric rotational osteotomy needs rather extensive soft tissue release, such as complete capsulotomy and resection of short external rotators and psoas tendons. Many patients tend to complain about the leg length discrepancy and limp due to varus change. We found soft tissue resection and limb shortening could be minimized by doing the osteotomy at the femur neck rather than the trochanteric area following the technique of surgical dislocation. It needs careful dissection of the posterior retinacular artery to preserve circulation to the femoral head. Methods. We have performed 17 cases (14 cases were in men and 3 cases were in women), and average patient age was 45 years old. Osteotomy was applied to cases with collapse or large necrotic region that seemed to be fail by core decompression. All cases showed collapse except one (ARCO 2-B) and 6 cases were ARCO 3-A, 5 cases were ARCO 3-B, 4 cases were ARCO 3-C and one case was ARCO stage 4. Seven cases were rotated anteriorly, and ten cases were rotated posteriorly. Amount of rotation was 63 to 170 degrees in posterior rotation (mean 100.8 degrees) and mean 48 degrees in anterior rotation. The size of the necrotic area was 301 degrees according to the Koo method (combined necrotic angle in mid-coronal and mid-saggital MRI scan). Results. Harris hip scores were improved from 62 to 88 points and VAS was from 8.4 to 2.6 in 13 cases. Conversion to THA was done in 4 cases (23.5%) as pain was persisting and there was one more failed case which was lost to follow-up. Another 2 cases showed insufficient circulation in bone SPECT, but no symptoms until recently. Problems with fixatives were in 4 cases and one case had heterotopic ossification without symptom. Conclusion. In conclusion, the outcome of the operation could be identified much earlier than other procedures. 12 cases (58.8%) showed satisfactory results and 2 cases were in observation due to insufficient circulation, and 5 cases (29.4%) failed. The operative technique will be revised and we are expecting better results

We aimed to report our initial experience with the use of cementless, rectangular, dual-taper, straight femoral stem (SL-PLUS) with bipolar head prosthesis in femur neck fractures. We operated 50 consecutive patients (28 women, 22 men; age ranged from 41 to 99 years; mean age 74) due to femur neck fractures and inserted the above-mentioned prosthesis. We used cemented femoral stem in severely osteoporotic patients. According to the Garden’s classification, there were 12 type II, 34 type III and 4 type IV fractures. We used direct lateral or posterolateral approach to insert the prosthesis. The entire operating time did not exceed 90 minutes and severe bleeding was not seen, in any patient. All patients were allowed to full weight bearing by a walker within the first postoperative 48 hours. We could evaluate the functional outcome of 25 patients who survived and had at least 6 months complete follow-up. We used Harris’ hip score for evaluation of the patients’ functional outcomes. Eight patients were lost to follow-up within the first postoperative 3 months, 15 patients died within the first postoperative 8 months and two patients could not walk due to an initial cerebrovascular disorder. The data of 15 patients, who passed away, showed that, mean age was 82 (70–99) years, 13 of 15 them were older than 75 years, 9 were man and 6 were woman, there were 2 type 2, 11 type 3 and 2 type 4 fractures. Mean age of the included patients was 70 (41–88) years. There were 18 women and 7 men. There were eight type II, 15 type III and 2 type IV fractures. After a mean follow-up period of 17 (6–27) months, the mean hip score of 25 patients was 77 (51–96) points. There were two excellent (90–100 pts), 7 good (80–89 pts), 12 fair (70–79 pts) and 4 poor (< 70 pts) functional outcomes. Similar mean hip scores were observed between ≤70 (77.9 pts) and > 70 years (75.8 pts) age groups (P=0.849), between man (78.0 pts) and woman (76.1 pts) patients (P=0.297) and between Garden type II (70.9 pts) and Garden types III–IV (79.3 pts) fractures (P=0.075). The rate of obtaining a satisfactory or fair functional outcome in the surviving elderly patients who were initially treated using a cementless, rectangular, dual-taper, straight femoral stem with bipolar head prosthesis due to femur neck fractures was 84% at the early postoperative period. Age, gender and type of the fracture do not influence the functional outcome. The risk of early postoperative mortality seems to increase in patients older than 75 years and with displaced fractures. This kind of prosthesis can be preferred to lessen the operation time, intraoperative bleeding, to avoid the peroperative complications due to bone cement application and to allow early postoperative rehabilitation in femur neck fractures of the geriatric population

A matched comparison was made between femoral neck-preserving short, tapered stems (n = 50) and conventional length femoral stems (n = 50) in cementless total hip arthroplasty between January 2008 and January 2012. Patients were matched for age, sex, body mass index, height, surgical approach, and surgeon. In group A, mean preoperative HHS and WOMAC scores of 55.0 and 53.0, respectively, improved to mean postoperative scores of 98.6 and 3.3, respectively, at an average follow–up of 37.2 months. In group B, mean preoperative HHS and WOMAC scores of 53.0 and 49.5, respectively, improved to mean postoperative scores 97.8 and 4.4, respectively, at an average follow–up of 35.3 months. In addition, no significant differences in mean postoperative HHS (P = 0.168) or WOMAC scores (P = 0.158) were observed between the two groups according to the independent sample t-test. Table 1 shows two stems (4%) located in valgus (greater than 5° from neutral). The mean preoperative and postoperative HHS and WOMAC scores were similar to those of stems neutrally located in group A. All group A stems displayed bone bridging and endosteal spot welds distributed in Gruen zones 2 and 6 as evidence of bony ingrowth with no radiolucencies (Fig. 1). Two patients in group B had the slight decrease in bone density, mostly in Gruen zone 1 and 7. No radiographic evidence of osteolytic lesions, cortical hypertrophy, or acetabular fractures was detected in either group. Furthermore, no patient required revision surgery for aseptic loosening. The chi–square (Fisher's exact) test showed no significant difference between the two groups with respect to patient complications (Table 2). One patient in group A with a CCD angle of 135° had subsidence (greater than 2 mm, P =0.313) that displayed bony ingrowth with no further progression of subsidence at final follow-up. An intraoperative minor femur neck fracture (P =1.00) occurred in two patients (one in group A and one in group B). These patients were treated by cerclage wires without further incident. Three patients (two in group A: valgus and a CCD angle 135°, and one in group B: varus) had malalignment (P = 0.554) that was not associated with loosening. One patient in group A with a CCD angle of 135° had greater than 1 cm leg length discrepancy (shortening, P = 0.313). Two patients in group B had thigh pain (P = 0.151) that disappeared after a few months. Three patients (one in group A and two in group B) had heterotopic ossifications (P = 0.554) that were categorized as Brooker class I in two patients and class II in one patient without limiting their activities. In conclusion, no significant differences in the clinical and radiographic outcomes as well as component-specific complications were observed between the two groups, showing satisfactory performance at the 5-year follow-up. Group A had a higher incidence of malalignment and subsidence and a lower incidence of thigh pain and proximal bone resorption than group B

Proximal femur fractures are common in the elderly population. The aim of this study was to determine the relationship between fracture type and proximal femoral geometric parameters.

We retrospectively studied the electronic medical records of 85 elderly patients over 60 years of age who were admitted to the orthopedic department with hip fractures between January 2016 and January 2018 in a training and research hospital in Turkey. Age, fracture site, gender, implant type and proximal femoral geometry parameters (neck shaft angle [NSA], center edge angle [CEA], femoral head diameter [FHD], femoral neck diameter [FND], femoral neck axial length [FNAL], hip axial length [HAL], and femoral shaft diameter [FSD]) were recorded. Patients with femoral neck fractures and femur intertrochanteric fractures were divided into two groups. The relationship between proximal femoral geometric parameters and fracture types was examined. SPSS 25.0 (IBM Corparation, Armonk, New York, United States) program was used to analyze the variables. Independent samples t test was used to compare the fracture types according to NSA, FHD, FND and FSD variables.

A statistically significant difference was found in FSD (p=0,002) and age (p=0,019). FSD and age were found to be greater in intertrochanteric fractures than neck fractures. Gender, site, CEA, FNAL, HAL, NSA, FHD and FND parametres were not significantly different.

In the literature, it is seen that different results have been reached in different studies. In a study conducted in the Chinese population, a significant difference was found between the two groups in NSA, CEA and FNAL measurements. In a study conducted in the Korean population, a significant difference was found only in NSA measurements. The FSD is generally associated with bone mineral densitometry in the literature and has been shown to be a risk factor for fracture formation. However, a study showing that there is a relationship between FSD and fracture type is not available in the literature.

In this study; FSD was found to be higher in intertrochanteric fractures (p = 0.002). However, for the clinical significance of this difference, we think that larger patient series and biomechanical studies are needed.

INTRODUCTION. THA as primary treatment for displaced femoral neck fractures in elderly still remains a prominent concern. Overall dislocation rate after total hip arthroplasty (THA) is reported form 1∼5%. But, it is quiet different in situation of femur neck fracture in elderly. The THA is associated with higher rates of dislocation (8%∼11%) in eldery compared to hemiarthroplasty even though THA showed better clinical and functional scores. Recently resurgence about THA using DMC comes after improvement of manufacturing technology. The aim of this prospective multicenter study is to assess the rates of dislocation and re-operation for displaced femoral neck fractures in elderly with THA with Dual Mobility Cup (DMC) and to review systematically comparison of previous reports. Up to our knowledge, this is first report from asian conutry about the clinical outcomes THA using DMC for displaced femur neck fracture in elderly. METHODS. Prospective consecutive groups of patients treated for displaced femoral neck fractures by three surgeons at each three center were included. 131 hips underwent THA with DMC for acute displaced femoral neck fracture in patients aged older than 70 years. Data regarding rates of dislocation and re-operation were obtained by review of medical records. Additionally From 2009 which the US FDA first approved the DMC, the authors searched reports regarding to THA using DMC for displaced femur neck fracture in elderly using the MEDLINE including cases series and comparative studies with bipolar hemiarthroplasty and THA. Therefore, current report was compared with previous reports. RESULTS. The reports about THA using DMC for displaced femur neck fracture in elderly were limited. Most of them comes from European countries. Comparative study with THA from Sweden reported the dislocation rate of THA using DMC with average aged 75-year is 0%. In Denmark study, the bipolar hemiarthroplasty showed 14% of dislocation rate for femur neck fracture in patient aged 75 years but, THA using DMC is 4.6%. Two cases series from French reported about 1–4% in patients aged 80 years. In our multicenter study, dislocation occurred in 6/131 hips (4.6%) treated with total hip arthroplasty using DMC for displaced femur neck fracture over 70 years older patients. Reoperations including periprosthetic fracture and fixation failure of cup were required in 1/43 (2.3%) hips treated with total hip arthroplasty using DM cup. These result is comparable to European reports. DISCUSSION AND CONCLUSION. Our findings indicate that THA with DMC can not guarantee to prevent the dislocation for high risk elderly patients, but the overall rate of dislocation can be comparable to those of bipolar hemiarthroplasty and reduced compared to conventional total hip arthroplasty. This result might be a valuable messages for burden of the medical cost by dislocation after arthroplasty especially for older patient. Therefore, adding advnatages of THA compared with hemiarthroplasty, the THA with DMC can be a wise option for displaced femoral neck fracture in eldely. But, the randomized controlled study still is needed to clarify to confirm this findings

Removal of bullets retained within joints is indicated to prevent mechanical blockade, 3rd body wear and resultant arthritis, plus lead arthropathy and systemic lead poisoning. The literature is sparse on this subject, with mostly sporadic case reports utilizing hip arthroscopy. We report on the largest series of removal of bullets from the hip joints using open surgical. We reviewed prospectively collected data of patients who presented to a single institution with civilian gunshot injuries that breached the hip joint between 01 January 2009 and 31 December 2022. We included all cases where the bullet was retained within the hip joint area. Exclusion criteria: cases where the hip joint was not breached, bullets were not retained around the hip area or cases with isolated acetabulum involvement. One hundred and eighteen (118) patients were identified. One patient was excluded as the bullet embedded in the femur neck was sustained 10 years earlier. Of the remaining 117 patients, 70 had retained bullets around the hip joint. In 44 patients we undertook bullet removal using the followingsurgical hip dislocation (n = 18), hip arthrotomy (n = 18), removal at site of fracture fixation/replacement (n = 2), posterior wall osteotomy (n = 1), direct removal without capsulotomy (tractotomy) (n = 5). In 26 patients we did not remove bullets for the following reasons: final location was extra-capsular embedded in the soft tissues (n=17), clinical decision to not remove (n=4), patients’ clinical condition did not allow for further surgery (n= 4) and patient refusal (n=1). No patients underwent hip arthroscopy. With adequate pre-operative imaging and surgical planning, safe surgical removal of retained bullets in the hip joint can be achieved without the use of hip arthroscopy; using the traditional open surgical approaches of arthrotomy, tractotomy and surgical hip dislocation

The neck is the firmer structure of the proximal femur designed to spread the stresses both in compression and tension towards the metadiaphisys and the greater trochanter. Therefore femural neck preserving in total hip arthroplasty allows an optimized stresses’ distribution to obtain both an optimal integration and a subsequent better bone remodelling. The solidity of the structure and the geometric architecture with a femural neck angle of 125° guarantee the maximum primary stability, especially torsional of the stem. At last femural neck retaining allows, when requested, the revision with a richer bone-stock. For the aforementioned reasons since 1979 I proposed the femural neck preservation making a short cementless stem named Biodinamica. From 1983 to 1996 I personally implanted 498 Biodinamica prostheses with very satisfactory results showing a long term survival of the 98% (f.up 13 to 17 years). In 1996 with Ing. Keller it has been created the C.F.P. stem with the T.O.P. acetabular cup as evolution of Biodinamica system. The improvements are critical: materials have changed (from Cr-Co-Mb to Ti alloy), coating and design too. We report clinical and radiographical results of 10 years of C.F.P. implants that showed a further improvement, not only about the prosthesis’ survival, but especially regarding their quality with a 91% excellent clinical outcome. In conclusion we report the 25 years experience retaining the femural neck in hip arthroplasty with Biodinamica (498) and after C.F.P. (445) of a complessive cases of 943 arthroplasty

To identify ideal screw placement for internal fixation of intra capsular fracture neck of femur to avoid fixation failures, 20 cadaveric bone measurements of the neck of femur in basal, midcervical and at sub capital regions were carried out using Vernial caliper and CT scan. Midcervical region of neck of femur measurements were further divided into upper half (Superior half) and Inferior half (Inferior Half). AP and Lateral view X-rays were obtained following three parallel screws placements in Femur neck:. Configuration 1: Triangular configuration where two screws are inferior and one superior. Configuration 2: Triangular configuration where two screws are placed superiorly and one screw inferiorly. Neck has wider diameter in the upper half of neck of femur than in the lower half in the mid cervical region. Placing two 7.0 mm cancellous screws (total 14 mm) in the lower half of the neck of femur, as widely practised, has more likely chances of not having purchase in the mid cervical region of the femur neck by at least one screw. Cannulated screws fixation carried out in reverse triangular configuration by placing two screws superiorly (superior-anterior and superior-posterior) and one screw inferiorly (inferior-central) has better fixation and avoids fixation failure. Reverse triangular configuration of fixation is also likely to support the weaker superior half of the neck which lacks stronger cortex and calcar part as in the inferior part of the neck. We also recommend placing a larger screw in the superior half of femur neck and a smaller screw in the inferior half in recon-–IM nail fixation, based upon our experiment result

Summary Statement. This work features a new approach to overcome drawbacks of commercial calcium phosphate cements in terms of application by on-site preparation and bone ingrowth by introduction of macropores in the material using a hydrofluoroalkane based aerosol foam. Introduction. The application of calcium phosphate bone cements (CPCs) into a void for example of an osteoporotic bone is very difficult as the cement paste is made outside the application site and subsequently applied into the damaged bone. A common drawback of especially apatitic cements is a very low resorption rate due to small pore size Therefore different approaches have been described to add macropores into the cement. 2. , leading to bone ingrowth and tissue penetration. The aim of this project is the use of two separate formulations in pressurised systems – a suspension and an emulsion – which can be mixed in a specially developed device and can be applied easily and efficiently into a bone directly during surgery leading to a self-hardening macro porous CPC foam. The intention is to fill voids in osteoporotic bones to ensure stability for implants like e.g. screws for femur neck fractures. An increased stability for implants can allow the possibility of a less invasive femur neck preserving therapy in contrast to a femur neck replacement. Other indications for such foam (i.e. kyphoplasty) are under evaluation. Methods. As suggested above two separate formulations for the components are developed to prevent premature hardening. Hydrofluoroalkanes were preferred as propellants to propane, butane or isobutane, due to their superior safety profile. The hardener component was formulated as propellant-in-water emulsion. Several parentally approved emulsifiers (e.g. Poloxamer 188) were tested in view of solubility at the given salt and binder concentration. The stability of resulting emulsions in pressurised containers, the corresponding foams as well as the foam expansion volume was analyzed. Porous hydroxyapatite is formed after addition of tetra-calciumphosphate, di-calciumphosphate dihydrate and tri-sodiumcitrat dehydrate incorporated in the suspension component. To overcome quick sedimentation of these solids, particle size was reduced by dry or non-aqueous wet milling, respectively. Changes in particle size distribution and enthalpy changes during processes were analyzed. Hardening properties of both components were tested particularly with regard to compressive strength. In order to apply the components, a suitable application system was developed and the hardened product analyzed using x-ray diffraction. Results. The optimised Ca. 2+. /(PO. 4. ). 3−. component is a submicron-sized suspension in a mixture of ethanol and HFA 134a. The development of the suspension led to new knowledge with regard to milling effects on the Ca. 2+. /(PO. 4. ). 3−. components. The optimised hardener component contains an aqueous solution of sodium phosphates, Povidone 90 and Poloxamer 188 emulsified in HFA 227. Both components are formulated in pressurised cans. Discussion/Conclusion. A two component bone foam for stabilisation in osteoporotic bones including a new mixing / application system, which allows actuation of the components and leads to a hardening process that results in hydroxyapatite in a suitable test setup, was developed. The new application system. Further steps i.e. proof of concept (in-vitro and in-vivo) are being taken

Resurfacing THA is claimed to transfer stress naturally to the femur neck and preserve proximal femoral bone mass postoperatively. DXA is an established method in estimating BMD around a standard THA, but due to the anteversion of the femur neck, rotation could affect the size of the neck-regions and thereby the BMD measurements around a RTHA. To our knowledge, this is the first study to analyze the effects of hip rotation on BMD in the femoral neck around a RTHA. We scanned the femoral neck of 15 patients twice in each position of 15° inward, 0° and 15° outward rotation, and analyzed BMD in a single and a six-region model. CVs were calculated for BMD in the same position as well as between different positions. For double measurements in the same position we found mean CVs of 3.1% (range 2.5% – 3.7%) and 4.6% (range 2.2% – 8.6%) in the one- and six-region models, respectively. When the 15° outward position was excluded, the CVs decreased to 2.8% and 4.0%. With rotation, the mean CVs rose to 5.4% (range 3.2%–7.2%) and 11.8% (range 2.7% – 36.3%). This effect was most pronounced in the 6-region model, predominantly in the lateral and distal parts of the femoral neck, where the change was significantly different from the fixated position. For the single-region model 15° rotation could be allowed without compromising the precision. We conclude that rotation adversely affects the precision of BMD measurements around a RTHA, but in the single-region model smaller rotations can be allowed. With the hip fixated the six-region model produces low CVs, acceptable for longitudinal studies. For maximal topographical detail we prefer the six-region model and recommend that future longitudinal DXA studies, including RTHA, be performed standardised, Preferably, with the hip in the neutral or internal rotation

Aims: The original M.E. Mueller straight stem is used as standard implant for primary hip replacement with cement fixation in our hospital since 1982. Methods: During the last 20 years in our department 5110 Mueller straight stems were implanted for hip replacement. 4054 cases of arthritis of the hip joint, 883 femoral neck fractures and 173 cases of revision were treated with this implant. 109 patients out of 1982 and 1983 were re-examined after 5 years clinical and radiological. After 20 years dates out of 128 patients of a group of 200 (65%) from 1982/83 are available. In a third group from 489 femur neck fractures cases between 1987 and 1996 101 patients could be verified and their complications analysed Results: After 5 years from 158 patients 26 had deceased and 23 were lost. In the remaining group were 9 local and 8 general complications. Two cases had revisions. After 20 years 72 out of 200 were lost 65 had deceased. From 128 patients in this trial 19 had a revision of stem. 109 patients still lived with their first replacement. The surveillance rate is 82,5%. In the group of 101 re-examined patients with straight stems after femur neck fracture 3 cases had revision, 2 out of dislocation and 1 with deep infection. Conclusions: With the experience of 5110 implantations of Mueller straight stems during the last 20 years, a very small rate of complications and a surveillance of 82,5% this implant is a standard in cemented fixation in primary hip replacement

INTRODUCTION. Experience with Metal on Metal (MoM) hip resurfacing devices has shown adequate cementation of the femoral head is critical for implant survival. Bone necrosis can be caused by the temperature change in the peri-prosthetic bone whilst the cement cures during implantation. This can lead to implant loosening, head/neck fracture and implant failure. During the implantation it is known that implants change shape potentially altering joint clearance and causing loosening. Given the history of Metal on Metal implant failure due adverse tissue reactions from Cobalt and Chromium particles we sought to test a novel Ceramic on Ceramic (CoC) bearing which may mitigate such problems. AIM. We set out to compare the behaviour of a novel ceramic femoral head component to a standard metal component in a hip resurfacing system after cemented implantation in a physiological warmed cadaveric model. Our first aim was to perform heat transfer analysis: To document time to, and extent of, maximum temperature change on the metal/ceramic surface and inside the resurfaced femoral head bone. Our second aim was to perform a dimensional analysis: To document any resulting deformation in the metal/ceramic femoral head bearing diameter during cementation. METHODS. Femurs were removed from four fresh frozen cadavers and placed into a vice. One surgeon with extensive experience in hip resurfacing surgery (JH) prepared all the femoral heads for implantation. Cadaveric warming was performed using a thermostatic silicone heating element to achieve near physiological conditions (28–32°C). The femur components were then implanted onto the femur head using Simplex P (Stryker) low viscosity bone cement. We used four ceramic (ReCerf™) and four metal implants (ADEPT®) of equal and varying size. (2 × (42mm, 46mm, 48mm, 50mm). Temperature change was measured using a thermometer probe placed into femur neck and head from the lateral side with position check using an image intensifier. Implant surface temperature was measured using a calibrated infrared thermometer at a standard 30cm distance. Head bearing surface diameter was measured using a micro-meter. Measurements were taken 2mins pre-implantation and sequentially at 1, 5, 10, 15, 20, 25 and 30 minutes after implantation. RESULTS. The bone temperature change for both metal and ceramic implants fell after implantation and then increased. The implant surface temperature increased and then stabilised for both implants. There was no significant difference in the bone or surface temperature change between metal and ceramic implants. The bearing surface diameter change was greater in the metal implants, although this was not significant. All implants returned to within one µm of initial surface diameter at 30 minutes. CONCLUSIONS. The femoral head component of a ceramic resurfacing has similar properties for surface temperature change following implantation to conventional MOM resurfacing. The periprosthetic bone is not at risk of significant heat necrosis during cementation (max temp 32°C). The deformation following implantation was similar for both metal and ceramic components. All implants returned to near initial diameter. The deformation and temperature changes following implantation of a ceramic resurfacing are similar to a metal implant

Purpose. We evaluated the clinical and radiographic outcomes of cementless bipolar hemiarthroplasty using rectangular cross-section stem for femoral neck fracture in elderly patients more than 80 years of age with osteoporosis. Material and Methods. 76(cemented 46, cementless 30) bipolar hemiarthroplasties for femur neck fracture were performed in elderly patients more than 80 years old. The mean follow-up period was 4.3 years (2 to 7 years). The Harris hip score at last follow-up and pre-postoperative daily living activity scale according to Kitamura methods were analyzed clinically. The radiological results were assessed using stability of femoral stem and other complications were evaluated. Results: At last follow-up, there were no significant differences of Harris hip score and daily living activity between two groups. Stem loosening and instability were not observed in cementless arthroplasty. There were 18 cases of osseous fixation in radiologic study. There were 1 case of dislocation and 1 case of superficial infection in cemented arthroplasty and 1 case of deep infection in cementless arthroplasty. Conclusion. Cementless bipolar hemiarthroplasty using rectangular cross-section stem for elderly patients with a femoral neck fracture showed satisfactory short-term clinical and radiological results compared to using cement stem

Introduction. Hip resurfacing arthoplasty (HRA) is an alternative to total hip arthroplasty (THA), which has increased in the last years, especially in young patients. A suitable positioning of the resurfacing head is important, mainly because it is strongly related with the neck fracture. The goal of this work was to evaluate the influence of the resurfacing head positioning in the load distribution along the femurs’ structures. Materials and methods. Using 3D scan technology, the exterior geometry of a composite femur, used to create the FE models, was obtained. Three resurfacing models were used in three different positions in the frontal plane. A model with a positive offset of +5mm (Resurfacing #1), in neutral position (Resurfacing #2), and with a negative offset of −5mm (Resurfacing #3) was developed. A Birmingham® Hip Resurfacing prosthesis was chosen according to the femurs’ head. It was positioned in the femur and acetabulum by an experimented surgeon. The metal on metal contact pair was implemented. Models were aligned with 7° and 9°, considering the position of the anatomical femurs in sagittal and frontal planes. Models were constrained on the wing of the ilium and ischial tuberosity, allowing only vertical and rotational movements on the iliac side. Femurs were constrained on its distal side, allowing only rotational movements. Results. The most important strains in four different aspects, anterior, posterior, medial and anterior were analyzed. The highest differences occurred on the medial alignment of femurs. Comparing models Resurfacing #1 and Resurfacing #2, the highest displacement increase (11%) comparatively at the neutral position was observed. Besides, comparing models Resurfacing #2 and Resurfacing #3, displacement decrease of 13% (resurfacing #3) in the same region was observed. Thus, one can conclude that: a positive offset increases the strains on the femurs neck; a negative offset decreases the strains on the same region. According to these results, one can state that the risk of neck fracture in resurfacing implants slightly increases as the resurfacing head is positioned with a positive offset. Beyond that region, differences are not relevant

In the past, the clinical outcome of earlier types of resurfacing hip arthroplasty was often characterised by a high percentage of failures and early mobilisations. An implant retrieval of a Co-Cr head and UHMWPE cup cemented resurfacing hip prosthesis was analysed. The implant was in place 11 years, without any clinical problem for nearly 10 years. The cup was highly worn. There was a complete fracture of the interface between cement and bone at the base of the femural neck. A significant hyperplastic reaction was present at the level of the synovial membrane, with fibrin deposits, hyperplasia of lining cells and a cellular infiltrate formed mostly by macrophages, with occasional giant cells and localised groups of perivascular lymphocytes. Immunohistochemical analysis showed that all lymphocytes were of the T type and that the largest part of macrophages containing debris were not activated. Inside the prosthetic head there were only traces of ossified tissue. This picture indicated that for a long time no viable bone tissue had been in contact with the cement and bone rarefaction was massive. The study shows an important cause of the failure of earlier types of hip resurfacing arthroplasty, namely the abnormal stress distribution that caused the complete bone rarefaction

The use of conventional stems in hip arthroplasty may be difficult in cases of dysplasia, coxa vara or coxa valga, after fracture or proximal femur osteotomy. In fact the morphologic alterations of the proximal femur might require prosthetic components characterised by small size and different neck angles to restore correct joint biomechanics. In these cases we are often compelled to compromise between the ideal implant aneiversion and fit and what we can really achieve. An alternative to conventional prostheses is represented by custom-made prostheses. For 3 years we have been using the Modulus stem in the treatment of morphologic disorders of the hip. The conic shape of the stem easily fits the different morphologies of the proximal femur, whereas the modularity of the neck makes it possible to correct length, inclination and declination of the femural neck. We studied 59 patients by clinical and radiographic examination before surgery and 1, 3, 6 and 12 months postoperatively. We recorded a statistically significant improvement in the clinical score already at 1 month but this was even better at 6 months after surgery, with respect to the pre-operative examination. With the use of this prosthesis, the recovery of correct joint biomechanics together with high tribologic standards could improve the implant survival, leading to cost reduction and patient satisfaction

Purpose: The use of femural head as an autograft in the reconstruction of dysplastic acetabulum is a fast, convinient and with excellent results throught time. Materlal-method: Since January 1986 until December 2002, 57 total hip replacements had taken place for dysplastic acetabulum. In all of them, the femural head has been used as an autograft. The age of the patients was between 42 to 75 years old (m.a. 63 ñ.Ï.). 45 of them were females and 12 males. 9 patients have been suggested to intertrïchanderic osteotomy in the past. One third of the patients had also the other hip affected. The surgical approach to the hip in all cases was made by the Harding’ s techique. The autograft in received from the femural neck. We prepared the acetabulum until we had bleeding bone. The bone graft is beared with two screws and if any gup exist is filled with cancellous autografts. In 41 operations of total hip replacements the cup was fixed with cement and in the rest 16 without. In our research we have included 43 hips with a follow-up from 3 to 14 years (m.a. 8,5 y.o.). Results: The results were evaluated with the Merle d’Aubigne and Postel scale. 5.6 pain, 4.1 wirdth of mobility. The callousness and the remodeling of the autograft were coplet in x-rays control. Íï case of absorbe of the bone graft. Until now no artrhoplasty has been revised. Conclusions: We consider that this is a satisflng method for filling and supporting the cup and in adittion it offers advantages in case that the artrhoplasty has to be revised

Purpose. There are some concerns about doing hip resurfacing arthroplasty in ONFH due to bone defect which can cause mechanical weakness of femoral component and highly active young age of patients which can cause high wear rate and failure rate. The purpose of this study is to verify the HRA is safe procedure in ONFH in the aspect of mechanical and biological issue. Materials and Methods. Between December 1998 and May 2005, 185 hips of 169 patients underwent MoM HRA using Birmingham Hip Resurfacing System® at single center. 166 hips (26 hips of female, 140 hips of male) of 144 patients have been reviewed for at least 7 years after MoM HRA. Mean follow-up period was 101.8 (84–178) months. Their mean age at the time of operation was 37.7(16–67) years old. Clinically, Harris hip scores (HHS), UCLA activity scores and range of motion were evaluated. Radiologically, the extent of necrotic area in preoperative MRI and radiolucency around implants, narrowing of retained neck, impingement, stress shielding, and heterotopic ossification were evaluated in the serial anteroposterior and groin lateral radiographs of hip. Complications were defined as joint dislocation, infection, implant loosening, femoral neck fracture and pseudotumor. Failure was defined as revision arthroplasty due to the complications. Results. The extent of necrotic area in preoperative MRI was average 37.6 (13.3–65)%. Clinically, average HHS was improved from 81.7 points to 98.5 points at last follow-up. Average UCLA activity score at last follow-up was 9.0 points. Range of motion at last follow-up was very satisfactory. There was no patient with severe pain around hip joint. Radiologically, radiolucency was shown around acetabular component in 2 cases (1.2%) and around stem of femoral components in 3 cases (1.8%). Fracture of femoral neck was seen in 1 case(0.6%). Moderate narrowing changes of retained femoral neck were noticed in 4 cases (2.4%). Impingement was seen in 12 cases (7.2%). We found only 1 case of osteolysis at Gruen zone III of acetabulum. Heterotopic ossification was found in 5 cases (3.0%). There was no case with hip dislocation, infection or pseudotumor. Revision surgeries after the primary resurfacing arthroplasty were performed in 4 cases (2.4%). Three hips were revised to the conventional total hip arthroplasty (THA) because of loosening of acetabular component and femur neck fracture. One case of femoral component loosening was revised to THA using big metal head with retained acetabular component. Conclusions. MoM HRA in ONFH demonstrates good survivorship in average 101.8 months follow-up study. Most of patients show excellent clinical results with high level of activity postoperatively. Prevalence of complications is extremely lower than concern including the allergic reaction to the metal ion. There was no mechanical failure related to bone defect due to ONFH. This results suggests that MoM HRA in ONFH less than 50% of extent of necrosis can be justified

The purpose of this study was to investigate the efficacy of oral alendronate for the older children with osteogenesis imperfecta. Eight boys and 6 girls with average age of 9.7 years were given oral alendronate, 10mg everyday for those > 35kg, 10mg every other day for those 20 – 35 kg, and 10mg every three days for those < 20 kg. Treatment period averaged 3.3 years (range, 2.1 to 3.6). The number of fractures decreased by 39% in the lower extremity, although not statistically significant. Ten patients or their parents reported improved well-being during the treatment period. Z score for bone mineral density improved from −3.75 to −1.18 in the lumbar spine, and from −3.84 to −2.74 in the femur neck. Restoration of the collapsed vertebral bodies was observed, and the metaphyseal bands appeared on the simple radiographs. Urinary excretion of calcium and N-telopeptide of type I collagen were decreased by 64% and 47%, respectively. Abdominal discomfort was reported in five patients, one of which needed temporary switch to intravenous protocol. Iliac crest biopsy including the physis showed expanded primary spongiosa area with numeric multi-nucleated cells, which had heterogenous immunoreactivity for osteoclast markers. This study revealed beneficial effects of oral alendronate in osteogenesis imperfecta patients, supported by radiological, biochemical and histological findings. We believe that oral alendronate is a more convenient method of bisphosphonate treatment for osteogenesis imperfecta, especially in older children