Aim. In the current study we aim to characterize the use of cationic host defense peptides (HDPs) as alternative antibacterial agents to include into novel antibacterial coatings for orthopedic implants. Staphyloccous aureus represent one the most challenging cause of infections to treat by traditional antibacterial therapies. Thanks to their lack of microbial resistance described so far, HDPs represent an attractive therapeutic alternative to antibiotics. Furthermore, HDPs have been showed to control infections via a dual function: direct antimicrobial activity and regulation of immune response. However, HDPs functions characterization and comparison is controversial, as changing test conditions or cell type used might yield different effects from the same peptide. Therefore, before moving towards the development of HDP-based coatings, we need to characterize and compare the immunomodulatory and antibacterial functions under the same conditions in vitro of 3 well-known cathelicidins: human LL-37, chicken CATH-2, and bovine-derived IDR-1018. Method. S. aureus, strain SH1000, was incubated with different concentrations of each HDP and bacterial growth was monitored overnight. Primary human monocytes were isolated from buffy coats using Ficoll-Paque density and CD14 microbeads, and differentiated for 7 days to macrophages. After 24h incubation in presence of LPS and HDPs, macrophages cytokines production was measured by ELISA. Macrophages cultured for 24h in presence of HDPs were infected with serum-opsonized S. aureus. 30 min and 24h after infection, bacterial phagocytosis and intracellular killing by macrophages were measured by flow cytometry and colony forming units (CFU) count respectively. Results. All HDPs efficiently inhibit macrophages LPS-mediated activation, as observed by a reduced production of TNF-α and IL-10. Despite a comparable anti-inflammatory action, only CATH-2 shows direct antibacterial properties at concentrations 10-times lower than those needed to stimulate immune cells. Although stimulation with HDPs fails to improve macrophages ability to kill intracellular S. aureus, IDR-1018 decreases the proportion of cells phagocytosing bacteria. Conclusions. In addition to a strong anti-inflammatory effect provided by all HDPs tested, CATH-2 has direct antibacterial effects while IDR-1018 reduces the proportion of macrophages infected by S. aureus. Use of these HDPs in combination with each other or with other conventional antibacterial agents could lead the way to the design of novel antibacterial coatings for orthopedic implants

Aim. Prosthetic joint infections pose a major clinical challenge. Developing novel material surface technologies for orthopedic implants that prevent bacterial adhesion and biofilm formation is essential. Antimicrobial coatings applicable to articulating implant surfaces are limited, due to the articulation mechanics inducing wear, coating degradation, and toxic particle release. Noble metals are known for their antimicrobial activity and high mechanical strength and could be a viable coating alternative for orthopaedic implants [1]. In this study, the potential of thin platinum-based metal alloy coatings was developed, characterized, and tested on cytotoxicity and antibacterial properties. Method. Three platinum-based metal alloy coatings were sputter-coated on medical-grade polished titanium discs. The coatings were characterized using optical topography and scanning electron microscopy with energy dispersive spectroscopy (SEM/EDS). Ion release was measured using inductively coupled plasma optical emission spectrometry (ICP-OES). Cytotoxicity was tested according to ISO10993-5 using mouse fibroblasts (cell lines L929 and 3T3). Antibacterial surface activity, bacterial adhesion, bacterial proliferation, and biofilm formation were tested with gram-positive Staphylococcus aureus ATCC 25923 and gram-negative Escherichia coli ATCC 25922. Colony forming unit (CFU) counts, live-dead fluorescence staining, and SEM-EDS images were used to assess antibacterial activity. Results. Three different platinum-based metal alloys consisting of platinum-iridium, platinum-copper, and platinum-zirconium. The coatings were found 80 nm thick, smooth (roughness average < 60 nm), and non-toxic. The platinum-copper coating showed a CFU reduction larger than one logarithm in adherent bacteria compared to uncoated titanium. The other coatings showed a smaller reduction. This data was confirmed by SEM and live-dead fluorescence images, and accordingly, ICP-OES measurements showed low levels of metal ion release from the coatings. Conclusions. The platinum-copper coating showed low anti-adhesion properties, even with extremely low metal ions released. These platinum-based metal alloy coatings cannot be classified as antimicrobial yet. Further optimization of the coating composition to induce a higher ion release based on the galvanic principle is required and copper looks most promising as the antimicrobial compound of choice. Acknowledgments. This publication is supported by the DARTBAC project (with project number NWA.1292.19.354) of the research program NWA-ORC which is (partly) financed by the Dutch Research Council (NWO); and the AMBITION project (with project number NSP20–1-302), co-funded by the PPP Allowance made available by Health-Holland, Top Sector Life Sciences & Health to ReumaNederland

Aim. Antibacterial activity of coatings based on metal and metal oxide nanoparticles (NPs) often depends on materials and biotic targets resulting in a material-specific killing activity of selected Gram-positive and Gram-negative bacteria, including drug-resistant strains. In this perspective, the NPs loading amount, the relative elemental concentration inside the nanogranular building blocks and the deposition method are of paramount importance when the goal is to widen the antimicrobial spectrum, but at the same time to avoid high levels of metal content to limit undesired toxic effects. Aim of the present study was evaluation of the antimicrobial properties of two multielement nanogranular coatings composed of Titanium-Silver and Copper and of Magnesium-Silver and Copper. Method. Ti-Ag-Cu and Mg-Ag-Cu NPs were deposited on circular cover glasses (VWR) by Supersonic Cluster Beam Deposition. Biofilm-producer strains of Staphylococcus aureus (methicillin susceptible and resistant), Staphylococcus epidermidis (methicillin susceptible and resistant), Escherichia coli (fully susceptible and producer of extended spectrum beta lactamases), and Pseudomonas aeruginosa (susceptible and multidrug-resistant) were selected. The abilities of the selected strains to adhere, colonize and produce biofilm on the discs coated with Ti-Ag-Cu or Mg-Ag-Cu NPs were compared to uncoated circular cover glasses which were used as growth control. Cytotoxicity was also evaluated in order to assess the biocompatibility of the newly synthesized NPs. Results. In comparison to uncoated controls, both coatings showed significant anti-adhesive properties against S. aureus, S. epidermidis, and E. coli. Reduction in adhesion to Mg-Ag-Cu coated discs was observed also for P. aeruginosa isolates, although differences vs uncoated controls did not reach statistical significance. Biofilm formation was reduced on discs coated with Mg-Ag-Cu compared to Ti-Ag-Cu and, again, coatings had a milder effect on P. aeruginosa, probably due to its exceptional capability of attachment and matrix production. These results were confirmed by the evaluation of bacterial colonization on nanoparticles-coated discs by means of confocal laser scanning microscopy. A viability of 95.8% and 89.4% of cells cultured in the presence of Ti-Ag-Cu and Mg-Ag-Cu discs, respectively, when compared to negative controls was observed, thus excluding cytotoxic effects on eukaryotic cells. Conclusions. The newly synthesized Ti-Ag-Cu and Mg-Ag-Cu coatings are able to limit bacterial adhesion colonization and biofilm production, thus highlighting the safe use of multi-element families of NPs as new strategies against bacterial attachment to the surface of biomedical implants. However, further studies addressing activity against P. aeruginosa and including a wide number of isolates are warranted

Periprosthetic joint infections (PJIs) and osteosynthesis-associated infections (OSIs) present significant challenges in trauma and orthopaedic surgery, substantially impacting patient morbidity, mortality, and economic burden. This concern is heightened in patients with pre-existing comorbidities, such as diabetes mellitus, which are not always modifiable at presentation. A novel intraoperative strategy to prevent these infections is the use of Defensive Antibacterial Coating (DAC), a bio-absorbable antibiotic-containing hydrogel applied to implant surfaces at implantation, acting as a physical barrier to prevent infection. The purpose of this study is to assess the use of a commercially available hydrogel (DAC), highlighting its characteristics that make it suitable for managing PJIs and OSIs in orthopaedics and traumatology. Twenty-five patients who underwent complex orthopaedic procedures with intraoperative application of DAC between March 2022 and April 2023 at a single hospital site were included. Post-operative assessment encompassed clinical, laboratory, and radiographic examinations. In this study, 25 patients were included, with a mean age of 70 ± 14.77 years and an average ASA grade of 2.46 ± 0.78. The cohort presented an average Charleston Comorbidity score of 5.45 ± 2.24. The procedures included 8 periprosthetic fractures, 8 foot and ankle surgeries, 5 upper limb surgeries, and 4 elective hip and knee surgeries. Follow-up assessments at 6 weeks and 6 months revealed no evidence of PJI or OSI in any patients, nor were any treatments for PJI or OSI required during the interim period. DAC demonstrated efficacy in preventing infections in high-risk patients undergoing complex orthopaedic procedures. Our findings warrant further investigation into the use of DAC in complex hosts with randomized control trials

Aim. We aimed to compare the in vitro antibacterial activity of Bioactive Glass (BAG) S53P4, which is a compound showing local antibacterial activity, to that of antibiotic-loaded polymethylmethacrylate (PMMA) against multidrug resistant bacteria from osteomyelitis (OM) and prosthetic joint infection (PJI) isolates. Method. We studied convenience samples of multidrug resistant (MDR) microorganisms obtained from patients presenting OM and prosthetic joint infection (PJI). Mixtures containing tryptic soy broth (TSB) and inert glass beads (2mm), BAG-S53P4 granules (0.5–0.8mm and <45 mm) and Gentamicin or Vancomycin-loaded PMMA beads were inoculated with methicillin-resistant Staphylococcus aureus (MRSA) and methicillin-resistant coagulase-negative Staphylococcus (MR-CoNS), Pseudomonas aeruginosa or Klebsiella pneumoniae isolates. Glass beads (2.0mm) were used as a control. Antibacterial activity was evaluated by means of time-kill curve, through seeding the strains on blood agar plates, and subsequently performing colony counts after 24, 48, 72, 96, 120 and 168 hours of incubation. Differences between groups were evaluated by means of two-way analysis of variance (ANOVA) and Bonferroni's t test. Results. Inhibition of bacterial growth started soon after 48 hours of incubation, reached zero CFU/ml between 120 and 168 hours of incubation for both antibiotic-loaded PMMA and BAG S53P4 groups, in comparison with inert glass (p< 0.05). No difference regarding time-kill curves between antibiotic-loaded PMMA and BAG S53P4 was observed. Moreover, despite no difference was observed between both Vancomycin - or Gentamicin-loaded PMMA and BAG groups, there was statistical difference between the effectiveness of all treatments (BAG included) against gram-positive cocci and gram-negative bacilli, the latter of which requiring longer time frames for the cultures to yield no bacterial growth. Conclusions. BAG S53P4 presented antibacterial properties as much as antibiotic-loaded PMMA for MDR bacteria producing OM and PJI, although presenting differences between its effectiveness against different bacterial groups

Introduction. The use of narcotic medications to manage postoperative pain after TJA has been associated with impaired mobility, diminished capacity to engage in rehabilitation, and lower patient satisfaction [1]. In addition, side effects including constipation, dizziness, nausea, vomiting and urinary retention can prolong post-operative hospital stays. Intraarticular administration of local anesthetics such as bupivacaine – part of a multimodal postoperative pain management regimen – reduces pain and lowers patients' length of stay [2]. In addition to its anesthetic activity, bupivacaine also has antibacterial activity, particularly against gram-positive bacteria [3]. We have developed a bupivacaine-eluting ultrahigh molecular weight polyethylene (Bupi-PE) formulation; we hypothesized that elution of bupivacaine from polyethylene could have both anesthetic and antibacterial effects in vivo. Methods. In Vivo Antibacterial Efficacy. A total of n=10 male Sprague Dawley rats (250 g) were used in this study. Polyethylene (control) or Bupi-PE plugs (2.5 mm diameter × 5 mm length) were implanted subcutaneously in the rat dorsum. After incision site closure, 5 × 10. 7. cfu of bioluminescent S. aureus were injected around the implants. Bioluminescent signal (photos/second) was measured daily. All rats were euthanized after one week. In Vivo Anesthetic Efficacy. A total of n=10 male Sprague Dawley rats (250 g) were used in this study. Polyethylene (control) and Bupi-PE plugs (2.5 mm diameter × 5 mm length) were implanted into rat knees via a lateral transcondylar approach (Figure 1a). Efficacy was determined by performing a walking track analysis using a highly sensitive Tekscan. ®. sensor (VHR, 5101) (Figure 1b). Walking tracks were performed at baseline (pre-surgery) and every 24 hours for two weeks. All rats were euthanized after two weeks. Results. In Vivo Antibacterial Efficacy. One control rat expired at day 3 and another one expired in day 7. None of the Bupi-PE rats expired during the study. Significantly less bacterial load was observed in rats receiving Bupi-PE, starting at 24 hr post implantation, continuing until the end of study (day 7) (Figure 2). In Vivo Anesthetic Efficacy. 24 hr post surgery, rats in the control group loaded their unoperated hindlimb significantly more than their operated hindlimb. Rats with the Bupi-PE implant loaded both their hindlimbs similarly (Figure 1c). Discussion. The antibiotic activity of the Bupi-PE against an acute S. aureus infection in the subcutaneous dorsum determined that bupivacaine elution from UHMWPE effectively eradicated bacteria within the implant perimeter. In the joint, the release of bupivacaine allowed prompt weightbearing and joint mobilization compared to controls. Conclusion. Bupivacaine-eluting UHMWPE effectively reduced bacterial load in murine subcutaneous dorsum and reduced postsurgical pain in a murine intra-articular model. This material can be promising for use as infection prophylaxis and pain management after TJA. For any figures or tables, please contact authors directly (see Info & Metrics tab above).

Prior work in the setting of MRSA (clinical isolate), showed that enhancement of Ti6Al4V with anodized nanotubes apparently disrupts the formation and adhesion of MRSA biofilm. The greater amount of cultured MRSA using effluent released from in vitro nanotube surfaces by sonication, compared with thermal plasma sprayed (TPS), indicated probable disruption of biofilm formation and adhesion. The use of nanosilver nanotubes in vivo in a rabbit model showed that after 1 week of infection followed by 1 week of vancomycin treatment, the nanotube MRSA level was 30% that of TPS, and the nanosilver nanotube MRSA level was only 5% of TPS. The implementation of the technology will enhance the remodeled bone locking ability of rough TPS, with surface nanotubes that provide antibacterial properties and increased bone adhesion. Lap shear tests of the nanotubes were performed according to ASTM F1044. In multiple tests, circular adhesive films bonded Ti6Al4V bars containing nanotubes with plain Ti6Al4V. The assemblies were suitably arranged in a tensile tester and pulled to shear failure. There were three modes of failure; shear failure within the adhesive, failure of the adhesive from the plain titanium, and shear failure of the nanotubes from the bar. Tests determined the shear strength of the adhesive and its bonding strength to bare titanium. ImageJ software determined the area of each of the three failure modes. From this analysis, the shear strength of the nanotubes of each sample was calculated. The analyses showed the shear strength of the nanotubes to be as high as 65MPa (9,500psi) with a more typical shear strength of 55MPa (8,000 psi), and several surfaces with 45MPa (6,000 psi). The literature presents models predicting the shear stress in bonded hip stems. Assuming the TPS with nanotubes performs similar to a bonded hip stem, owing to the locking of the bone with the TPS, a typical shear stress prediction for physiological loads is approximately 10 MPa. The nanotube shear strengths were 4–6 times higher than the expected stress during use. For any figures or tables, please contact authors directly

Aim. The aim of this study was to establish an implant-associated osteomyelitis model in rats with the ability to quantify biofilm formation on implants for prospective evaluation of antibacterial effects on micro-structured implant surfaces. Method. Staphylococcus aureus (strain 36/07) suspension with infection concentrations of 106, 105, 104 and 10. 3. CFU/10µl, respectively was injected in the tibia of 32 rats (n=8 per group). Afterwards a titanium implant (0.8×0.8×12 mm) was inserted. 8 rats were implanted with a preincubated implant (107 CFU/ml, 12 h) and 8 rats served as a control (injection of 0.9% NaCl). During the follow up, clinical, radiographic and µ-CT examinations were conducted. On day 21 post op, all rats were sacrificed. Implant and tibia were explanted under sterile conditions. The implant was stained with green and red fluorescent nucleic acid dye (live/ dead) and analyzed by confocal microscopy. The amount of vivid and dead biomass as well as vivid bacteria on the implant surface was calculated with an image software*. Results. In all groups with artificial infection, local bacterial colonization could be detected without systemic infection. While clinical signs of infections (lameness, subcutaneous abscesses) decreased, the volume of bacterial colonization increased on the implant surface with decreasing initial infection CFU. Preincubated implants showed a similar bacterial colonialization of the surface as implants which were infected with 106 CFU as well as a similar bone disintegration due to ongoing osteomyelitis. Conclusions. Establishment of the implant-associated infection model in rats with subsequent quantification of the vivid bacterial volume via confocal microscopy was successful and is now applicable for the evaluation of micro-structured antibacterial implant surfaces. Pre incubation of implants with initiating biofilm formation was established as alternative onset of infection. This work was part of BIOFABRICATION for NIFE and funded by Volkswagen Foundation and MWK. * Imaris® ×64 6.2.1

Aim. The treatment of osteomyelitis often requires extensive surgical debridement and removal of all infected tissues and foreign bodies. Resulting bone loss can then eventually be managed with antibacterial bone substitutes, that may also serve as a regenerative scaffold. Aim of the present study is to report the clinical results of a continuous series of patients, treated at our centre with an antibacterial bioglass*. Method. From November 2010 to May 2016, a total of 106 patients, affected by osteomyelitis, were included in this prospective, single centre, observational study. Inclusion criteria were the presence of osteomyelitis with a contained bone defect or segmental defects < 10 mm, with adequate soft tissue coverage. All patients underwent a one-stage procedure, including surgical debridement and bone void filling with the bioactive glass*, with systemic antibiotic therapy and no local antibiotics. Clinical, radiographic and laboratory examinations were performed at 3, 6 and 12 months and yearly thereafter. Results. Two patients were lost to follow-up, hence a total of 104 patients (65 males, 39 females; mean age: 46 ± 17 years, min 6 – max 81) were available at an average follow-up of 38 ± 26 months (range: 12 – 68); forty-eight patients (46.1%) were classified as Type A, 48 (46.1%) as Type B and 8 (7.7%) as Type C hosts, according to McPherson classification. Tibia (N=61) and femur (N=33) were the most common involved bones. On average patients had undergone 2.1 ± 1.3 (min 0 – max 7) previous surgical operations, with a mean infection duration of 18.7 ± 16.6 months (min 2 – max 120). Infection recurrence was observed in 10 patients (9.6%), most often within one year from surgery (8/10). Negative prognostic factors included infection duration > 2 years, Gram negative or mixed flora or negative cultural examination, Type B or C hosts and soft tissue defect. No side effects or complications related to bioglass were noted. Conclusions. This is to our knowledge the longest and the largest single centre consecutive series of patients, affected by bone infections of the long bones, treated according to a one-stage procedure using bioactive glass. Our results confirm, on a larger population and at a longer follow-up, previous reports. Early treatment, pathogen identification and adequate management of soft tissues should be considered to further reduce infection recurrence rate. *BonAlive®

The aim of the study is to evaluate the effect of acrylic cement CMW1 (DePuy) containing 2,5% of gentamicin and addition of 5 % and 10 % of respective vancomycin, meropeneme and ceftriaxone on growth inhibition of reference strains of MRSA, E. faecalis, S. aureus, P. aeruginosa and E. coli. From every portion of investigated acrylic cement CMW1 discs were cut with a diameter of 15mm and a thickness of 5mm, average weight 1.365 g (+/− 0,257g). Inoculum was prepared with the reference strains: MR3 S. aureus methicillin-resistant (MRSA), ATCC 29219 E. faecalis, ATCC 25923 S. ureus, ATCC 27853 P. aeruginosa and ATCC 25922 E. coli. A colonies of bacteria taken from a 18-hour culture on solid medium were addend to tubes with sterile physiological saline solution to obtain a density of 0.5 McFarland (5 × 105 CFU / ml). The suspension was distributed evenly over the Mueller-Hinton (MH) medium (Biomerieux, France). Prepared discs of CMW1 cement were put with a sterile forceps on the plate with a dry medium. The plates were incubated aerobically at 24 hr and the temp. 37°C. After 24 hours the diameter of zone of inhibition of bacterial growth on a plate was measured (in mm) and average size of the inhibition zone was calculated. The CMW1 cement inhibited to a comparable degree growth of reference strains with the exception of E. faecalis. The addition of vancomycin increased by 1/5 inhibitory potential of CMW1 cement on growth of MRSA, S. aureus, P. aeruginosa and E. coli. and significantly for E. faecalis. Changing the concentration of vancomycin, meropeneme and ceftriaxone from 5% to 10% do not increased the inhibitory potential of CMW1 cement on the growth of MRSA, S. aureus, P. aeruginosa, E. coli and E. faecalis. Addition of meropeneme increased inhibitory potential of CMW1 cement against MRSA by 1/3, P. aeruginosa and E. coli by ½, E. faecalis by 3/4 and against S. aureus by 100%. Addition of ceftriaxone to CMW1 cement increased the inhibiting of the growth of MRSA similiarly to 5% and 10% of vancomycin, E. faecalis as meropeneme 5% and 10 %, while the growth of S. aureus and P. aeruginosa, less than meropeneme. Addition of antibiotics to acrylic cement increased its antibacterial properties. Increase if vancomycine concentrations from 5 to 10% had no stronger antibacterial effect

Bacterial contamination of endoprostheses especially in revision surgery is an upcoming problem according to increasing number of joint replacements. Early adherence of bacteria producing a biofilm is difficult to treat. Silver coating of implants offers the opportunity to avoid bacterial adhesions acting against all relevant bacteria causing infections on the implant. We developed a new technique of nano-silver coating using elemental silver covered with SiOxCy whose thickness can be varied determing duration of the coating on the implant. The SiOxCy and silver is completely soluble at least at 3 months. The silver coatings used so far are measuring at least 10um and they are not soluble making a cementless implantation of the endoprostheses impossible. The aim of this study was to test the compatibility of the new combined coating with human osteoblastic cells.

The test was carried out with fHOB 1.19 (ATCCR CRL-11372TM). The cells were cultivated in 1:1 mixture of DMEM/Ham's F12 with usual supplements. The protein content was measured colourimetrically using BCA reagents and staining of the cells was done with XTT-reagent (Roche). The cells were incubated on Titanium and PEEK with and without coating for 2,6,16 and 48 hours.

No adverse effects of the silver coating on the early cell adhesion at 2 and 6 hours and the further proliferation at 16 and 48 hours were observed. The adhesion on Titanium showed no significant difference against coated Titanium but an improvement of cell adhesion was seen on coated PEEK.

This soluble silver coating did not negatively influence human osteoblastic cells. As the complete surfacing is soluble it might be possible to combine early protection against bacteria and osseous integration. An animal study is in progress verifying the in vitro results. It should investigate the maximum duration of the coating on the implant not disturbing osseous integration.

In order to improve fast osseointegration, to modulate inflammatory response and to avoid biofilm formation, several attempts of surface modifications of titanium alloy in term of surface topography and chemistry have been performed over years, but this is still an open issue. In our research work, a patented chemical treatment was developed and tailored to improve fast osseointegration and to allow further surface functionalization in order to get a multifunctional surface. After the chemical treatment, Ti6Al4V shows a micro and nano-textured surface oxide layer with high density of hydroxyls groups, as summarized Figure 1: it is able to induce apatite precipitation (during soaking in Simulated Body Fluid), high wettability by blood, specific protein adsorption, positive osteoblast response and surface mechanical resistance to implantation friction. Hydroxyl groups exposed by the treated surface also allow binding natural biomolecules such as polyphenols, which can further improve the rate and quality of osseointegration by adding anti-inflammatory, antibacterial and antitumoral effects suitable for implants in critical situations. Polyphenols have the further added value of being a low cost and eco-sustainable product, extractable from byproducts of wine and food industry. On the chemically treated and functionalized samples, the surface characterization was performed using Folin&Ciocalteu test, fluorescence microscopy and XPS analysis in order to check the presence and activity of the grafted biomolecules (polyphenols from red grape pomace and green tea leaves). Cell tests were performed with Kusa A-1 cells highlighting the ability of polyphenols to improve osteoblasts differentiation and deposition of mineralized extracellular matrix. Surface functionalization can also be performed with chitin derived biomolecules to reduce inflammation. With the purpose of obtaining the antibacterial effect, during the chemical treatment a silver precursor can also be added to obtain in situ reduced silver nanoparticles embedded in the nano-structured oxide layer. The samples containing nanoparticles on the surface were characterized by means of TEM and FESEM observation highlighting the presence of well distributed and small-sized nanoparticles on the surface and through the thickness of the oxide layer. A long-lasting release in water was observed up to 14 days and antibacterial tests on Staphylococcus aureus showed the ability of the surface to reduce bacteria viability avoiding biofilm formation. The results showed that the patented chemical treatment can improve the response of osteoblasts to titanium alloy implants, but is also a promising way to obtain multifunctional surfaces with antibacterial, antioxidant, anti-inflammatory and antitumoral properties that can be the future of orthopedic implants

This study aimed to determine the optimal formulation of antibiotic-loaded bone cement (ALBC) for periprosthetic joint infection (PJI) using both in vitro and in vivo models incorporating various combinations of gram-positive and gram-negative antibiotics. The in vitro antibiotic release characteristics and antibacterial capacities of ALBCs loaded with either 4 g of vancomycin or teicoplanin and 4 g of ceftazidime, imipenem, or aztreonam were measured against methicillin-susceptible S. aureus, methicillin-resistant S. aureus, coagulase-negative staphylococci, Pseudomonas aeruginosa and Escherichia coli. ALBC spacers with superior in vitro antibacterial capacity were then implanted into ten patients (five females and five males between 29 and 75 years of age) diagnosed with chronic hip/knee PJIs and antibacterial activities within joint fluid were measured. The average duration of ALBC spacer implantation was 80 days (range, 36–155 days). Antibiotic concentrations and antibacterial activities of joint fluid at the site of infection were measured during the initial period as well as several months following spacer implantation. Cement samples loaded with vancomycin/ceftazidime or teicoplanin/ceftazidime exhibited equal or longer antibacterial duration against test bacteria as compared with other ALBCs. Joint fluid samples exhibited antibacterial activity against the test microorganisms including ATCC strains and clinically isolated strains. There were no adverse systemic effects, infection at second stage re-implantation, or recurrent infection at final follow-up. Vancomycin/ceftazidime ALBC provided broad antibacterial capacity both in vitro and in vivo and was shown to be an effective and safe therapeutic measure in the treatment of hip/knee PJIs. We thank H.Y. Hsu for performing bioassay

Staphylococcus aureus is the most frequently isolated organism in periprosthetic joint infections. The mechanism by which synovial fluid (SF) kills bacteria has not yet been elucidated, and a better understanding of its antibacterial characteristics is needed. We sought to analyze the antimicrobial properties of exogenous copper in human SF against S. aureus. SF samples were collected from patients undergoing total elective knee or hip arthroplasty. Different S. aureus strains previously found to be sensitive and resistant, UAMS-1 and USA300 WT, respectively, were used. We performed in-vitro growth and viability assays to determine the capability of S. aureus to survive in SF with the addition of 10µM of copper. We determined the minimum bactericidal concentration of copper (MBC-Cu) and evaluated the sensitivity to killing, comparing WT and CopAZB-deficient USA300 strains. UAMS-1 evidenced a greater sensitivity to SF when compared to USA300 WT, at 12 (p=0.001) and 24 hours (p=0.027). UAMS-1 significantly died at 24 hours (p=0.017), and USA300 WT survived at 24 hours. UAMS-1 was more susceptible to the addition of copper at 4 (p=0.001), 12 (p=0.005) and 24-hours (p=0.006). We confirmed a high sensitivity to killing with the addition of exogenous copper on both strains at 4 (p=0.011), 12 (p=0.011), and 24 hours (p=0.011). Both WT and CopAZB-deficient USA300 strains significantly died in SF, evidencing a MBC-Cu of 50µM against USA300 WT (p=0.011). SF has antimicrobial properties against S. aureus, and UAMS-1 was more sensitive than USA300 WT. The addition of 10µM of copper was highly toxic for both strains, confirming its bactericidal effect. We evidenced CopAZB-proteins involvement in copper effluxion by demonstrating the high sensitivity of the mutant strain to lower copper concentrations. Thus, we propose CopAZB-proteins as potential targets and the use of exogenous copper as possible treatment alternatives against S. aureus

Background. Although described as a commensal bacterium with low pathogenicity, Cutibacterium acnes involvement has been reported in many clinical entities: infections associated with devices, such as shoulder prosthetic joint infections, osteosynthesis, breast implants or cerebrospinal fluid shunts. Various studies show that C. acnes grows as a biofilm, contributing to its persistence by allowing its escape from the action of the immune system and antibiotics. Purpose. Our aim was to assess the activity of different active substances (erythromycin, clindamycin, doxycycline and Myrtacine. ®. ) on eight different well-characterized C. acnes strains after growth in biofilm mode. Methods. Eight susceptible strains of C. acnes were selected for this study, including two reference strains (ATCC6919 and ATCC11827) and six clinical strains. All C. acnes strains were studied using two different methods to study the biofilm production at different time points: the BioFilm Ring Test. ®. technique (early stages of adhesion) and the Crystal Violet (CV) method (mature biofilm). In a second step, the impact of different active substances (erythromycin, clindamycin, doxycycline and Myrtacine. ®. ) was studied. For the CV technique, two types of tests were performed: preventive tests (addition of active substances and bacteria at the same time) and curative challenge tests (addition of active substances on a biofilm already formed after 48h). Transmission electron microscopy was performed to investigate the morphology modifications. Results. C. acnes isolates from phylotypes IA. 1. and IA. 2. , seem to produce more mature biofilm in the first stages of adhesion than other phylotypes. Curative assays were performed to evaluate the efficacy of antibiotics and Myrtacine. ®. on mature biofilm. Significant efficacy of Myrtacine. ®. at 0.03% was observed for C. acnes strains. Moreover, the combination of Myrtacine. ®. and doxycycline appears to decrease the total biofilm biomass. The effect of doxycycline as a preventive measure was minimal. On the contrary, a similar use of Myrtacine. ®. as early as 0.001% showed significant efficacy with a significant decrease in total biofilm biomass for all C. acnes strains. Transmission electron microscopy revealed a significantly decreased biofilm growth in treated bacteria with Myrtacine. ®. compared to untreated bacteria. Moreover, the total number of bacteria decreased as the concentration of Myrtacine. ®. increased suggesting also an antimicrobial effect. Conclusion. These results confirm the difference in biofilm producing ability depending on C. acnes phylotypes. These results suggest that Myrtacine. ®. may be a promising alternative antibacterial and anti-biofilm agent like peroxide de benzoyle to prevent shoulder prosthetic joint infection involving planktonic and biofilm C. acnes

Aim. To develop a new system for antibacterial coating of joint prosthesis and osteosynthesis material. The new coating system was designed to release gentamicin immediately after insertion to eradicate surgical contamination. Method. Steel implants (2×15mm) were coated with a solid nanocomposite xerogel made from silica and the dendritic polymer, hyperbranched polyethyleneimine. The xerogel was anchored inside a porous surface made by pre-coating with titanium microspheres. Finally, gentamicin was encapsulated in the xerogel, i.e. no chemical binding. A total of 50 µg gentamicin was captured into each implant. The efficacy of the new coating was evaluated in a porcine model of implant associated osteomyelitis. In total, 30 female pigs were randomized into 3 study groups (n=10). Group A; plain implants + saline, Group B; plain implants + 10. 4. CFU of Staphylococcus aureus, and Group C; coated implants + 10. 4. CFU of S. aureus. Implant + inoculum was placed into a pre-drilled implant cavity of the right tibia and the pig was euthanized 5 days afterwards. Postmortem microbiology and pathology were performed. Two additional pigs were used in a pharmacokinetic study where microdialysis (MD) catheters were placed alongside coated implants. Extracellular fluid was sampled regularly for 24 hours from the MD catheters and analyzed for gentamicin content. Results. Within Groups A and C, all implants were found sterile by sonication and bacteria could not be identified within the surrounding bone tissue. In contrast, all Group B animals had S. aureus positive implant and tissue microbiology. Macroscopic and microscopic pathological examinations confirmed that Group A and C animals were complete identic, i.e. no pus around implants and only minor peri-implant inflammation related to insertion of implants per se. All Group B animals had pus around their implants and a massive peri-implant inflammatory response dominated by neutrophil granulocytes. Maximum gentamicin release (35 µg /mL) was measured in the first obtained MD sample, i.e. after 30 min, and the concentration stayed above the MIC level for the used S. aureus strain for 8 hours. Conclusions. The new xerogel coating prevented development of osteomyelitis. Prevention was due to a fast gentamicin release immediately following insertion and antimicrobial active concentrations were detectable several hours after implantation. This means that the critical time point of most relevant surgical procedures potentially could be protected by the novel coating. The new coating will be investigated on larger scale implants and full-size prosthesis in the future

Objectives. Investigate the incorporation of an antibiotic in bone cement using liposomes (a drug delivery system) with the potential to promote osseointegration at the bone cement interface whilst maintaining antibiotic elution, anti-microbiological efficacy and cement mechanical properties. Prosthetic joint infection and aseptic loosening are associated with significant morbidity. Antibiotic loaded bone cement is commonly used and successfully reduces infection rates; however, there is increasing resistance to the commonly used gentamicin. Previous studies have shown gentamicin incorporated into bone cement using liposomes can maintain the cement's mechanical properties and improve antibiotic elution. The phospholipid phosphatidyl-l-serine has been postulated to encourage surface osteoblast attachment and in a liposome could improve osseointegration, thereby reducing aseptic loosening. Preliminary clinical isolate testing showed excellent antimicrobial action with amoxicillin therefore the study aims were to test amoxicillin incorporated into bone cement using liposomes containing phosphatidyl-l-serine in terms of antibiotic elution, microbiological profile and mechanical properties. Methods. Amoxicillin was encapsulated within 100nm liposomes containing phosphatidyl-L-serine and added to PMMA bone cement (Palacos R (Heraeus Medical, Newbury, UK)). Mechanical testing was performed according to Acrylic Cement standards (ISO BS 5833:2002). Elution testing was carried out along with microbiological testing utilising clinical isolates. Results. Liposomal encapsulated amoxicillin PMMA bone cement exceeded minimum ISO BS 5833:2002 standards, had better elution at 12.9% when compared with plain amoxicillin (p=0.036 at 48 hours) or commercial gentamicin cement (Palacos R+G, Heraeus Medical, Newbury, UK – previous studies showed 6% elution over the same time period). Amoxicillin showed superior antimicrobial action when compared with gentamicin of the same concentration. However, liposomal encapsulated amoxicillin in solution and liposomal encapsulated amoxicillin in PMMA were both less effective than free amoxicillin in bacterial growth inhibition. The liposomal amoxicillin also seemed to decrease the cement setting time. Conclusions. Phosphatidyl-l-serine containing liposomes maintained the cement's mechanical properties and seemed to have better antibiotic elution, however, had less effective antibacterial action than plain amoxicillin. This difference in antibacterial action requires further investigation along with investigation of osteoblast attachment to phosphatidyl-l-serine containing liposomes within cement. Plain amoxicillin, for those not penicillin allergic, seems to be a credible alternative to gentamicin for incorporation in PMMA bone cement. It has shown superior antibacterial action, which may improve infection rates, whilst maintaining the cement's mechanical properties

Recent clinical data suggest improvement in the fixation of tibia trays for total knee arthroplasty when the trays are additive manufactured with highly porous bone ingrowth structures. Currently, press-fit TKA is less common than press-fit THA. This is partly because the loads on the relatively flat, porous, bony apposition area of a tibial tray are more demanding than those same porous materials surrounding a hip stem. Even the most advanced additive manufactured (AM) highly porous structures have bone ingrowth limitations clinically as aseptic loosening still remains more common in press-fit TKA vs. THA implants. Osseointegration and antibacterial properties have been shown in vitro and in vivo to improve when implants have modified surfaces that have biomimetic nanostructures designed to mimic and interact with biological structures on the nano-scale. Pre-clinical evaluations show that TiO. 2. nanotubes (TNT), produced by anodization, on Ti6Al4V surfaces positively enhance the rate at which osseointegration occurs and TNT nano-texturization enhances the antibacterial properties of the implant surface. 2. In this in vivo sheep study, identical Direct Metal laser Sintered (DMLS) highly porous Ti6Al4V specimens with and without TNT surface treatment are compared to sintered bead specimens with plasma sprayed hydroxyapatite-coated surface treatment. Identical DMLS specimens made from CoCrMo were also implanted in sheep tibia bi-cortically (3 per tibia) and in the cancellous bone of the distal femur and proximal tibia (1 per site). Animals were injected with fluorochrome labels at weeks 1, 2 and 3 after surgery to assess the rate of bone integration. The cortical specimens were mechanically tested and processed for PMMA histology and histomorphometry after 4 or 12 weeks. The cancellous samples were also processed for PMMA histology and histomorphometry. The three types of bone labels were visualized under UV light to examine the rate of new bony integration. At 4 weeks, a 42% increase in average pull-out shear strength between nanotube treated specimens and non-nanotube treated specimens was shown. A 21% increase in average pull-out shear strength between nanotube treated specimens and hydroxyapatite-coated specimens was shown. At 12 weeks, all specimens had statistically similar pull-out values. Bone labels demonstrated new bone formation into the porous domains on the materials as early as 2 weeks. A separate in vivo study on 8 rabbits infected with methicillin-resistant Staphylococcus aureus showed bacterial colonization reduction on the surface of the implants treated with TNT. In vitro and in vivo evidence suggests that nanoscale surfaces have an antibacterial effect due to surface energy changes that reduce the ability of bacteria to adhere. These in vivo studies show that TNT on highly porous AM specimens made from Ti6Al4V enhances new bone integration and also reduce microbial attachment

Aim. Bacteriophages, viruses specific of bacteria, are receiving substantial attention as alternative antibacterial agents to treat bacteria frequently multi-resistant to antibiotics and/or able to form biofilms, such as staphylococci. The latter are responsible for very difficult to treat bone and joint infections (BJIs). In this context, our consortium aims to develop a production of therapeutic phages in accordance with the will of ANSM (French National Agency for the Safety of Medicines and Health Products) to encourage the development of a national academic platform for phage therapy. We report the isolation and characterization of new anti-Staphylococcus phages as well as the evaluation of their activity on a collection of clinical strains of S. aureus (SA) and coagulase-negative staphylococci (CNS) in order to assess their therapeutic potential. Method. Seventeen phages were isolated from wastewater samples. Their identification was obtained by Illumina whole genome sequencing. To evaluate their spectrum of activity, 30 genetically characterized SA strains representative of the main genetic backgrounds as well as 32 strains belonging to 7 CNS species responsible for BJIs were included. The spot test technique, based on the determination of the Efficiency Of Plating ratio, was used (EOP, ratio between the phage titer obtained on a tested strain/titer on a reference strain, close to 1 if high sensitivity to the phage). Results. All isolated phages belonged to the Myoviridae family: 14/17 and 3/17 to the Kayvirus and Silviavirus genera respectively. Silviavirus phages were more active on SA strains (EOP>0.001 for 73–90% of strains) than Kayvirus phages (EOP>0.001 for 13–70% of strains, except for V1SA21: 80%). In total, 83% of strains were susceptible to the phage with the broadest spectrum in each genus, their combination representing a promising opportunity to prevent the emergence of resistance. Kayvirus phages had polyvalent activity on several CNS species (maximum 47% of tested strains), mainly S. lugdunensis, S. capitis and S. caprae, whereas Silviavirus phages were only active on 6–12% of the tested strains. Conclusions. We report the characterization of a large collection of novel phages with complementary spectra against a collection of SA and CNS strains. Further work is currently focused on i) the isolation of anti-S. epidermidis phages, bacterial species against which the present collection of phages was insufficiently active, while it is a major pathogen in this context, ii) the development of production and purification protocols in order to meet the requirements of ANSM for human use

Aim. Staphylococcus epidermidis (S. epidermidis) is one of the main pathogens responsible for bone and joint infections especially those involving prosthetic materials (PJI). Although less virulent than S. aureus, S. epidermidis is involved in chronic infections notably due to its ability to form biofilm. Moreover, it is frequently multiresistant to antibiotics. In this context, the development of additional or alternative antibacterial therapies targeting the biofilm is a priority. Method. The aim of this study was to evaluate in vitro the activity of phage lysin exebacase (CF-301) against biofilms formed by 19 S. epidermidis clinical strains responsible for PJI. We determined the remaining viable bacteria inside the biofilm (counting after serial dilution and plating) and the biomass (bacteria and extracellular matrix, using crystal violet staining) after 24h of exposition to exebacase at different concentrations, alone (0.05; 0.5; 5; 50 and 150 mg/L) or in combination (5, 50 and 150 mg/L) with antibiotics commonly used to treat multi-resistant S. epidermidis PJI (rifampin (1 mg/L), vancomycin (10mg/L) and daptomycin (10mg/L)). In this study, synergy was defined as a significantly higher effect of the association in comparison to the sum of the effect of each molecule. Results. Exebacase showed a dose-dependent reduction of biomass, ranging from 11 % at 0.5 mg/L to 66 % at 150 mg/L. Exebacase showed a significant bactericidal activity at 50 and 150 mg/l, with a mean decrease of the inoculum of 0.94 and 1.7 log, respectively. In addition, synergistic effects were observed in association with i) rifampin (1 mg/L) showing a mean decrease up to 84% of the biomass and 3.5 log CFU at 150 mg/L of exebacase, ii) vancomycin (10 mg/L) showing a mean decrease up to 81% of the biomass and 2.82 log CFU at 150 mg/L of exebacase, iii) and daptomycin (10 mg/L) showing a mean decrease up to 85% of the biomass and 3.1 log CFU at 150 mg/L of exebacase. Conclusions. Exebacase showed, in vitro, synergistic activity with antibiotics against S. epidermidis biofilms. It is a promising adjuvant therapy to rifampin, vancomycin and daptomycin in the context of PJI. Further studies are needed, in vitro to understand the mechanism of action on S. epidermidis biofilm and the heterogeneity of strain behaviour and in vivo to confirm the present data