Advertisement for orthosearch.org.uk
Results 1 - 6 of 6
Results per page:
Orthopaedic Proceedings
Vol. 104-B, Issue SUPP_13 | Pages 89 - 89
1 Dec 2022
Kitzen J Paulson K Edwards B Bansal R Korley R Duffy P Dodd A Martin R Schneider P
Full Access

Dual plate constructs have become an increasingly common fixation technique for midshaft clavicle fractures and typically involve the use of mini-fragment plates. The goal of this technique is to reduce plate prominence and implant irritation, as these are common reasons for revision surgery. However, limited biomechanical data exist for these lower-profile constructs. The study aim was to compare dual mini-fragment orthogonal plating to traditional small-fragment clavicle plates for biomechanical non-inferiority and to determine if an optimal plate configuration could be identified, using a cadaveric model. Twenty-four cadaveric clavicles were randomized to one of six groups (n=4 per group), stratified by CT-based bone mineral content (BMC). The six different plating configurations compared were: pre-contoured superior or anterior fixation using a single 3.5-mm LC-DC plate, and four different dual-plating constructs utilizing 2.4-mm and 2.7-mm reconstruction or LC-DC plates. The clavicles were plated and then osteotomized to create an inferior butterfly fracture, which was then fixed with a single interfragmentary screw (OTA 15.2B). Axial, torsional, and bending (anterior and superior surface loading) stiffness were determined for each construct through non-destructive cyclic testing, using an MTS 858 Bionix materials testing system. This was followed by a load-to-failure test in three-point superior-surface bending. Kruskal-Wallace H and Mann-Whitney U were used to test for statistical significance. There were no significant differences in BMC (median 7.9 g, range 4.2-13.8 g) for the six groups (p=1.000). For axial stiffness, the two dual-plate constructs with a superior 2.4-mm and anterior 2.7-mm plate (either reconstruction or LC-DC) were significantly stiffer than the other four constructs (p=0.021). For both superior and anterior bending, the superior 2.4-mm and anterior 2.7-mm plate constructs were significantly stiffer when compared to the 3.5-mm superior plate (p=0.043). In addition, a 3.5-mm plate placed anterior was a stiffer construct than a superior 3.5-mm plate (p=0.043). No significant differences were found in torsional stiffness or load-to-failure between the different constructs. Dual plating using mini-fragment plates is biomechanically superior for fixation of midshaft clavicle fractures when compared to a single superior 3.5-mm plate and has similar biomechanical properties to a 3.5-mm plate placed anteriorly. With the exception of axial stiffness, no significant differences were found when different dual plating constructs were compared to each other. However, placing a 2.4-mm plate superiorly in combination with a 2.7-mm plate anteriorly might be the optimal construct, given the biomechanical superiority over the 3.5-mm plate placed superior


Orthopaedic Proceedings
Vol. 94-B, Issue SUPP_XL | Pages 192 - 192
1 Sep 2012
Tomaszewski P Verdonschot N Bulstra S Verkerke G
Full Access

For amputated patients, direct attachment of upper leg prosthesis to the skeletal system by a percutaneous implant is an alternative solution to the traditional socket fixation. Currently available implants, the OPRA system (Integrum AB, Göteborg, Sweden) and the ISP Endo/Exo prosthesis (ESKA Implants AG, Lübeck, Germany) [1-2] allow overcoming common soft tissue problems of conventional socket fixation and provide better control of the prosthetic limb [3], higher mobility and comfort [2, 4]. However, restraining issues such as soft-tissue infections, peri-prosthetic bone fractures [3, 5–8] and considerable bone loss around the stem [9], which might lead to implant's loosening, are present. Finally, a long a residual limb is required for implant fitting. In order to overcome the limiting biomechanical issues of the current designs, a new concept of the direct intramedullary fixation was developed. The aim was to restore the natural load transfer in the femur and allow implantations in short femur remnants (Figure 1). We hypothesize that the new design will reduce the peri-prosthetic bone failure risk and adverse bone remodeling. Generic CT-based finite element models of an intact femoral bone and amputated bones implanted with 3 analyzed implants were created for the study. Models were loaded with two loading cases from a normal walking obtained from the experimental measurements with the OPRA device [10-11]. Periprosthetic bone failure risk was evaluated by considering the von Mises stress criterion [12-14]. Subsequently the strain adaptive bone remodeling theory was used to predict long-term changes in bone mineral density (BMD) around the implants. The bone mineral content (BMC) change was measured around implants and the results were visualized in the form of DXA scans. The OPRA and the ISP implants induced the high stress concentration in the proximal region decreasing in the distal direction to values below physiological levels as compared with the intact bone. The stresses around the new design were more uniformly distributed along the cortex and resembled better the intact case. Consequently, the bone failure risk was reduced as compared to the OPRA and the ISP implants. The adaptive bone remodeling simulations showed high bone resorption around distal parts of the OPRA and the ISP implants in the distal end of the femur (on average −75% ISP to −78% OPRA after 60 months). The bone remodeling simulation did not reveal any bone loss around the new design, but more bone densification was seen (Figure 2). In terms of total bone mineral content (BMC) the OPRA and the ISP implants induced only a short-term bone densification in contrast to the new design, which provoked a steady increase in the BMC over the whole analyzed period (Figure 3). In conclusion, we have seen that the new design offers much better bone maintenance and lower failure probability than the current osseointegrated trans-femoral prostheses. This positive outcome should encourage further developments of the presented concept, which in our opinion has a potential to considerably improve safety of the rehabilitation with the direct fixation implants and allow treatment of patients with short stumps


Orthopaedic Proceedings
Vol. 95-B, Issue SUPP_9 | Pages 17 - 17
1 Feb 2013
Monsell F Bellemore M Bilston L Goodship A Barnes J
Full Access

We investigated the effect of adjuvant and neoadjuvant chemotherapy regimens on the tibial regenerate after removal of the external fixator in a rabbit model of distraction osteogenesis using New Zealand white rabbits. Forty rabbits were randomly distributed into two groups. In the neoadjuvant group, half of the rabbits received 1mg/kg cisplatinum & 2mg/kg adriamycin at eight weeks of age followed by 1mg/kg cisplatinum & 4mg/kg adriamycin at ten weeks of age. The remaining ten received an identical volume of normal saline using the same regimen. The adjuvant group differed only in the timing of the chemotherapy infusion. Half received the initial infusion ten days prior to the osteotomy, with the second infusion four days following the osteotomy. Again, the remaining ten rabbits received an identical volume of normal saline using the same regimen. This produced an identical interval between infusions and identical age at osteotomy in both groups. All rabbits underwent a tibial osteotomy at 12 weeks of age. Distraction started 24hours after osteotomy at a rate of 0.75mm a day for 10 days, followed by 18 days without correction to allow for consolidation of the regenerate. At week 16 there was no difference in Bone Mineral Density (BMD), Bone Mineral Content (BMC) or volumetric Bone Mineral Density (vBMD) in the adjuvant group. Neoadjuvant chemotherapy appears to have a significant detrimental effect on BMD, vBMD and BMC. Despite this there were no significant alterations in the mechanical properties of the regenerate. Histologically there was a trend for increased cortical thickness in the control groups compared to intervention however this did not prove statistically significant. In conclusion, adjuvant chemotherapy may be more beneficial for cases where distraction osteogenesis is being considered to replace segmental bone loss after tumour excision


Orthopaedic Proceedings
Vol. 94-B, Issue SUPP_XLI | Pages 42 - 42
1 Sep 2012
Hooper G Gilchrist N Frampton C Maxwell R Heard A Mcguire P
Full Access

Bone mineral density (BMD) and bone mineral content (BMC) have not been previously assessed in unicompartmental knee replacement (UKR). We studied the early bone changes beneath the uncemented Oxford medial UKR. Our hypothesis was that this implant should decrease the shear stresses across the bone-implant interface and result in improved BMD and BMC beneath the tibial component. Using the Lunar iDXA and knee specific software we developed 7 regions of interest (ROI) in the proximal tibia and assessed 38 patients with an uncemented Oxford UKR at 2 years. We measured the replaced knee and contralateral unreplaced knee using the same ROI and compared the BMD and BMC. The initial precision study in 20 patients demonstrated high precision in all areas. There were 12 males and 16 females with an average age of 65.8 years (46–84 years). ROI 1 and 2 were beneath the tibial tray and had significantly less BMC (p=0.023 and 0.001) and BMD (p=0.012 and 0.002). ROI 3 was the lateral tibial plateau and this area also had significantly less BMC (p=0.007) and BMD (p=0.0001). ROI 4 and 5 immediately below the tibial keel had no significant change. These changes were independent of gender and age. These results were surprising in that the universal loss of BMC and BMD suggested that bone loading of the proximal tibia was not improved even after a UKR. The better BMD and BMC adjacent to the keel confirms other studies that show improved bone in-growth around keels and pegs in the uncemented tibial component. A prospective longitudinal study has been developed to compare BMD and BMC changes over time to see whether these changes are dynamic


Orthopaedic Proceedings
Vol. 94-B, Issue SUPP_XLI | Pages 12 - 12
1 Sep 2012
Birke O McDonald M Morse A Liu M Ke D Little D
Full Access

Sclerostin is a negative regulator of osteoblast differentiation and bone formation. Expressed by osteocytes, it acts through antagonising the Wnt/â-catenin pathway and/or BMP activity. Distraction osteogenesis, used for limb lengthening and reconstruction, can be complicated by disuse osteopenia and poor healing response, both of which would benefit from pro anabolic therapy. We examined the effects of Sclerostin Antibody (Scl-AbIII, Amgen Inc.,) in a rat model of distraction osteogenesis. A femoral osteotomy was stabilized with an external fixator in male Sprague Dawley rats. After a week of latency, the gap was distracted twice daily for 14 days to a total of 7 mm. Saline or Scl-Ab was administered twice weekly throughout the distraction period and up to 4, 6 or 8 weeks post commencement of distraction. Three groups were examined: Saline, Continuous Scl-Ab throughout the study (C Scl-Ab), and Delayed Scl-Ab with commencement of Scl-Ab after distraction (D Scl-Ab). Regenerate bone mineral content (BMC), determined by DEXA, was increased 36% at 4 weeks and 86% at 6 weeks with C Scl-Ab, resulting in a 65% increase in bone mineral density (BMD) at 6 weeks, compared with Saline (p<0.01). D Scl-Ab treatment showed a 41% increase in BMC and a 31% increase in BMD compared with Saline at 6 weeks (p<0.05). At 8 weeks, C Scl-Ab remained significantly increased over Saline (72% in BMC; 60% in BMD). Micro-CT scans of the regenerate revealed increases in bone volume of 88% with C Scl Ab and 65% with D Scl-Ab compared with Saline at 6 weeks (p<0.05). By 8 weeks, these increases were 36% for C Scl-Ab (p<0.05) and 37% for D Scl-Ab compared with Saline (p<0.01). Importantly, mean moment of inertia was increased over two-fold in both Scl-Ab groups at 6 weeks compared with Saline (p<0.05). Histology at 6 weeks confirmed micro-CT data with 85–88% increases in bone volume/tissue volume (BV/TV) in the regenerate with both C Scl-Ab and D Scl-Ab compared with Saline (p<0.05). Analysis of bone formation at 6 weeks revealed increases in mineral apposition rate of 56% in C Scl-Ab and 52% in D Scl-Ab compared with Saline (p<0.05). Scl-Ab treatment increased bone formation in this model of distraction osteogenesis, resulting in a larger regenerate callus (increased BMC and BV/TV). We expect further studies to reveal increases in mechanical strength. Scl-Ab may hold promise as a therapeutic to accelerate regenerate formation and consolidation in distraction osteogenesis for limb reconstruction


Orthopaedic Proceedings
Vol. 94-B, Issue SUPP_XXXVIII | Pages 33 - 33
1 Sep 2012
Almaawi A Rowas SA Chalifour L Petit A Haddad R Antoniou J Mwale F
Full Access

Purpose. Developmental exposure to estrogens has been shown to affect a number of organ systems, including long and short bones. Epigenetic effects of DES exposure have been shown to affect the third generation of progeny. Furthermore, recent studies have shown that environmental exposure to estrogen-like compounds is much higher than originally anticipated. This study aims to discover the effect of in utero exposure to a well-known estrogen agonist, diethylstilbestrol (DES), on lumbar bone, intervertebral disc (IVD), and articular cartilage. Femoral bone was studied to determine the specificity of the effect. Method. C57bl/6n pregnant mice were dosed orally with vehicle (peanut oil) or 0.1, 1.0 and 10 g/kg/day of DES on gestational days 11–14. Male and female pups were allowed to mature without further treatment until 3 months of age, at which point they were divided into swim and sedentary groups. After sacrifice, bone mineral density (BMD), bone mineral content (BMC), bone area (BA), and trabecular bone area (TBA) of the lumbar vertebrae and femur were measured using a PIXImus Bone Densitometer System (GE Medical Systems). Glycosaminoglycan (GAG) content (proteoglycan) was measured by the DMMB assay. Histological analysis of proteoglycan was performed with Safranin O staining. Intervertebral disc height was measured using NDP software (Leeds, UK). Statistical analysis was performed using analysis of variance (ANOVA) followed by Fisher's Protected Least Significant Difference (PLSD). A p-value of < 0.05 was considered statistically significant. Results. At all the doses studied, DES had no significant effect on lumbar and femoral BMD in both males and females. The lumbar BMC, however, was significantly increased in female swims at both the highest and lowest dose of DES, while the femoral BMC was only increased at the highest. The males, on the other hand, showed a decreased BMC at the highest dose of DES for both lumbar and femoral bone. Female swim group had an increased BA at the highest dose of DES while the male swims showed a decreased BA for femoral bone. The TBA showed a similar pattern. GAG analysis of lumbar IVDs showed a decrease at the lowest doses but a significant increase at the highest doses for both swim and sedentary groups. Histology showed morphological changes of the IVD and articular cartilage for all doses of DES. Conclusion. The effect of in utero DES exposure is more important on lumbar than on femoral bone. The effect was mainly observed at high dose of DES, except for BA that is also affected by low dose DES in lumbar bones. Results suggest that environmental estrogen contaminants might impact developmental lumbar bone growth and mineralization in mice. Further studies measuring the impact of environmental estrogen mimics, such as bisphenol A, are then warranted