The objective of this study is to determine the knee joint forces when rising from a kneeling position. We have developed a new type of knee prosthesis which is capable of attaining Japanese style sitting. To run the simulations and experiments needed to assess the performance of this prosthesis, it is necessary to know what forces act on the knee during deep flexion. Because these data are lacking, we created a 2D mathematical model of the lower leg to help determine knee joint forces during deep flexion. Healthy subjects of ten males (age of 25±4years, height of 170.3±9.1cm, and weight of 67.0±22.2kg) and five females (25±3years, 161±7.1cm, 47.7±6.2kg) participated in the experiment. Ground reaction force and joints angles were measured using a force plate and a motion recording system respectively. The collected data were entered into our mathematical model, and the muscle forces and the knee joint forces were calculated. To verify our model, we first used it to run simulation of middle and high flexions of the knee joint. In vivo data for these actions are available in the literature, and the results from our simulation were in good agreement with these data. We then collected the data and run simulation when rising from a kneeling position under the conditions shown in Fig. 1. They were a) double leg rising (both legs are aligned) without using the arms, b) ditto but using the arms, c) single leg rising (legs are in the front and the rear respectively) without using the arms, and d) ditto but using the arms. We obtained the following results. The statistics of the maximum values on the single knee joint for each condition were; a) Fmax=5.1±0.4 [BW: (force on the knee joint)/(body weight)] at knee flexion angle of Q=140±8°, b) Fmax=3.2±0.9[BW] at Q=90±10°, c) Fmax-d=5.4±0.5[BW] at Qd=62±20° for the dominant leg and Fmax-s=3.0±0.5[BW] at Qs=138±6° for the supporting leg respectively, and d) Fmax-d=3.9±1.5[BW] at Qd=70±17° for the dominant, and Fmax-s=2.1±0.5 [BW] at Qs=130±11° for the supporting. We may conclude that the single leg rising should be recommended since the maximum knee joint force did not become large as long as the knee was at deep flexion. The values introduced in this study could be used to assess the strength of the knee prosthesis at deep flexion. To obtain more realistic values of the joint forces, it is necessary to determine the ratio of the forces exerted by the mono-articular and the bi-articular joint muscles

INTRODUCTION. Applying the proper amount of tension to knees collateral ligaments during surgery is a prerequisite to achieve optimal performance after TKA. It must be taken into account that lower values of ligament tension could lead to an instable joint while higher values could induce over-tensioning thus leading to problems at later follow-up: a “functional stability” must then be defined and achieved to guarantee the best results. In this study, an experimental cadaveric activity was performed to measure the minimum tension required to achieve functional stability in the knee joint. METHODS. Ten cadaveric knee specimens were investigated; each femur and tibia was fixed with polyurethane foam in specific designed 3D-printed fixtures and clamped to a loading frame. A constant displacement rate of 0.05 mm/s was applied to the femoral clamp in order to achieve joint stability and the relative force was measured by the machine: the lowest force guaranteeing joint stability was then determined to be the one corresponding to the slope change in the force/displacement curve, representing the activation of the elastic region of both collateral ligaments. The force span between the slack region and the found point was considered to be the tension required to reach the functional stability of the joint. This methodology was applied on intact knee, after ACL-resection and after further PCL-resection in order to simulate the knee behavior in CR and PS implants. The test was performed at 0, 30, 60 and 90° of flexion using a specifically designed device. Each configuration was analyzed three times for the sake of repeatability. RESULTS. Results demonstrated that an overall tension of 40–50N is sufficient to reach stability in native knee with intact cruciate ligaments. Similar values appear to be sufficient in an ACL-resected knee, while higher tension is required (up to 60N) for stability after ACL and PCL resection. Moreover, the tension required for stabilization was slightly higher at 60° of flexion compared to the one required at the other angles, reflecting thus the mid-flection instability behavior. DISCUSSION AND CONCLUSIONS. The results are in agreement to other experimental studies. 1,2. and show that the tensions necessary to stabilize a knee joint in different ligament conditions are way lower than the ones usually applied via tensioners nowadays. To reach functional stability, surgeons should consider such results intraoperatively to avoid laxity, mid-flexion instability or ligament over-tension

Aim. This study evaluated target tissue concentrations of double dose cefuroxime administered intravenously as either one 15 min infusion of 3,000 mg (Group 1) or two single 15 min infusions of 1,500 mg administered 4 h apart (Group 2). Method. Sixteen pigs were randomised into two groups of eight. Cortical and cancellous bone, synovial fluid of the knee joint and subcutaneous adipose tissue concentrations were measured based on sampling via microdialysis. Plasma samples were collected as a reference. Comparison of the groups was based on time with concentrations above relevant minimal inhibitory concentrations (fT>MIC) of 4 μg/mL. Results. The mean time fT>MIC (4 μg/mL) across compartments was longer for Group 2 (280–394 min) than for Group 1 (207–253 min) (p<0.01). Cortical bone showed a tendency towards longer fT>MIC (4 μg/mL) in Group 2 (280 min) than in Group 1 (207 min) (p=0.053). Within 50 min after administration, the mean concentration of 4 μg/mL was reached in all compartments for both groups. The mean concentrations decreased below 4 μg/mL after approximately 4 h (Group 1) and 3 h (Group 2) from initiation of administration (time zero). Conclusions. During an 8 h interval, double-dose cefuroxime administered as 2 × 1,500 mg with a 4 h interval provides longer time above MIC breakpoint for Staphylococcus aureus (4 μg/mL) than a single bolus of 3,000 mg cefuroxime. To maintain sufficient tissue concentrations during longer surgeries, re-administration of cefuroxime (1,500 mg) should be considered 3 h after the first administration

The contact condition in the human knee joint must play important roles especially in dynamic loading situations where the loads transfer in the knee. In this study, the impact stress propagations through the inside of the knee joint were simulated using the three-dimensional finite element analysis (FEA). And the differences in the stress distribution were investigated between the intact knee and the total replacement condition. The finite element (FE) models of an intact human knee joint and a total replaced knee joint were constructed with high shape fidelity. The intact model included the cortical bone, cancellous bone, articular cartilage, bone marrow, and meniscus. And the total replacement knee FE model, which is consisted of the artificial femoral and tibial components were also prepared to compare the impact propagations with the intact model (Figure 1). Impact load were applied to the proximal femur of the FE models under the same conditions as those of the weight-drop experiments with the knee joint specimens. The FEA results showed that the impact stress propagated to the tibia through the knee joint for several milliseconds. The values and the time dependent change of the compressive strain on the cortical surface had good agreement with the experimental results. The compressive stress mainly propageted at the medial side, with 1.0 MPa at 1.2 milliseconds. Especially, the impact stress propagated not only in the cortical surface area which has hard material property but also in the soft cancellous bone region inside the knee joint. The mass density of the cancellous bone has similar to that of the cortical bone, and thus the role of the load bearing in the cancellous area must be much increasing under the impact condition. In the total replacement model, concentration of the impact compressive stress was observed with 2.8 MPa at the tibial region, while not under the normal intact conditions (Figure 2). Since the total replacement model is formed of different materials and the impact propagations were inhibited by the interfacial condition, such as sliding or debonding, it is considered that the contact condition between such materials have a great effect on the stress propagation

Aim. Little is known about microbiological spectrum and resistance patterns as well as the clinical outcome in patients who undergo a repeat first stage procedure as part of a 2-stage revision arthroplasty for the treatment of periprosthetic hip and knee joint infections. Methods. Between 2011 and 2019, a total of 327 2-stage revision arthroplasties were performed on 312 patients with PJI of the knee and hip at our institution. We performed a retrospective analysis of all patients, who underwent a repeat first stage procedure regarding re-revision rate, host factors, culture negative and positive stages, monomicrobial and polymicrobial infections as well as microbiological spectrum and antimicrobial resistance patterns. Results. Overall, 52/312 (16.7%) patients (27 knee/25 hip) underwent a repeat first stage procedure. There were 35/52 (67.3%) culture positive first, 17/52 (32.7%) culture positive repeat first and 12/52 (23.1%) culture positive second stage procedures. In 13/52 (25%) patients a re-revision surgery was necessary at a median follow-up of 46.8 months (range, 12.2 to 93.3 months). High re-revision rates (10/12 [83.3%]) were found in patients with culture positive second stage and low re-revision rates (3/40 [7.5%]; p<0.01) were found in patients with culture negative second stage. The microbiological spectrum changed in 9/11 (81.8%) patients between culture positive first and repeat first stage, in 3/4 (75%) patients between culture positive repeat first and second stage and in 5/6 (83.3%) between culture positive second stage and subsequent re-revision surgery. Moreover, the antimicrobial resistance pattern changed in 6/9 (66.7%) of persistent microorganisms. Conclusion. Microbiological results during first, repeat first and second stage procedures significantly impacted the re-revision rates and changes in microbiological spectrum and resistance patterns between stages are common. However, if eradication of the microorganism at second stage can be accomplished, low re-revision rates can be achieved, even in patients who require a repeat first stage procedure

The Total Knee Replacement (TKR) has been used as the effective treatment for osteoarthritis of the knee. The load of the knee joint is generally applied at the heel strike as the impact loading. In the elderly who had muscle weakness or weakening eyesight, it can be anticipated that more excessive loads are often added to the knees when they stumble or trip over. And the varus / valgus alignments of the femur and tibia differs among patients. However, most finite element analyses considering the effect of the alignments have rarely been performed. In this study, the mounting angle of the tibia component in the TKR knee was changed, and the effect of the change on the load transfer was assess using finite element analyses. Based on the CT images, the three-dimensional finite element models of the natural knee joint and TKR knee joint were created [Fig. 1]. Each model was constructed from hexahedoral elements with the isotropic material. The numbers of nodes and elements were 10,666 and 8,677 respectively. Under normal alignment, 5 degrees of varus, and 5 degrees of valgus knee, the static analyses at an applied load of 1000N and impact analyses at an applied load of 50 kg were performed. LS-DYNA ver760 software was used for the analyses. The finite element analyses results showed that under the static loading, no stress shielding was observed in the tibial cancellous bone of the intact knee or TKR knee, and the maximum compressive stress was 1.5 MPa. While under the impact loading, the compressive stress generated inside of the cancellous bone was three times higher in the TKR knee joint than that in the intact knee, and the load transfer time was reduced. This result reveals that the cancellous bone have load bearing function especially in the impact condition. When the impact load was applied to the varus and valgus TKR knee, the stress shielding was observed in the tibial cancellous bone, especially in the varus condition. In a case where the tibia component was mounted by tilting it at −5 to 5 degrees depending on the varus/valgus of the knee, the stress shielding was alleviated; the distribution of load was almost the same as that of the TKR knee joint model under the normal alignment [Fig.2]. The effect of a slight difference in the alignment on the stress distribution is expected to be a contributor to determine artificial knee joint shape, loading condition, and other design factors in developing revision arthroplasty or custom-made implant

Aim

Unexpected negative-cultures (UNC) are a common diagnostic problem in periprosthetic joint infection (PJI) of the hip and knee when using culture-based methods. A novel molecular approach (MC)1 based on the identification of the vast majority of bacterial species in a single assay using species-specific bacterial interspacing region length polymorphisms and phylum-specific 16S rDNA sequence polymorphisms has demonstrated clinical utility in PJI diagnostics (1). In addition, MC provides an estimate of the leukocyte concentration in the specimen analysed. The aim of this retrospective, blinded study was to evaluate the performance of MC in identifying the microbiological content and determining the leukocyte count in synovial fluid (SF) collected from hip and knee revision arthroplasty cases with UNC. It was also assessed whether antibiotic treatment would have been changed if the result from MC had been known.

Abstract

The objective of this study is to investigate the effect of the tensile force ratio between the two extensor muscles for the hip joint on the forces acting on the knee joint. We have created a mathematical model of lower limb and have performed some simulations to introduce the forces acting on the knee joint for various daily activities. With only one exception, our results for knee joint forces were in good or close agreement involving all range of knee flexion either with the in vivo data or other literature data. The exception was that, at high knee flexion angle (knee bend), the tangential components of knee joint force became pretty larger than those from the in vivo data, while the normal components did not differ much with each other though as shown in Fig. 1. We considered that the above mentioned discrepancy was attributed to the fact that in order to solve an indeterminate problem, we had assumed the hamstrings and the gluteus maximus work together with the same force with each other, thereby introducing the hamstrings force too great. Then we expected that the above discrepancy could be eliminated if we change the tensile force ratio between the hamstrings and the gluteus maximus basing upon a certain biomechanical criterion, for example the biological cross-sectional areas. Thus we modified our model so that we could introduce the knee joint forces as a function of the tensile force ratio. Simulation was performed for the various tensile ratio values and it was found that the knee joint force was sensitively affected by the tensile ratio and the above mentioned discrepancy between the simulation results and the in vivo data could be eliminated if the ratio value was appropriately chosen. Figure 2 shows the situation; Variations of Fn and Ft as a function of knee angle q for the various tensile force ratio r between the hamstrings and the gluteus maximus. Where, r=1.56 was determined from the biological cross-sectional areas of the hamstrings and the gluteus maximus and r=4.5 was determined so that the simulation results best fit to the in vivo data. It has been criticized that there exist large variations of knee joint forces obtained from model analyses. And the reasons for this have been attributed to for example such facts that the model is 2D and the parameter values are incorrect. Yet, another important issue may be to find out the way how to determine the value of the synergetic muscles' force ratio with reflecting a biological rationality

INTRODUCTION. In patients with neural disorders such as cerebral palsy, three-dimensional marker-based motion analysis has evolved to become a well standardized procedure with a large impact on the clinical decision-making process. On the other hand, in knee arthroplasty research, motion analysis has been little used as a standard tool for objective evaluation of knee joint function. Furthermore, in the available literature, applied methodologies are diverse, resulting in inconsistent findings [1]. Therefore we developed and evaluated a new motion analysis framework to enable standardized quantitative assessment of knee joint function. MATERIALS AND METHODS. The proposed framework integrates a custom-defined motion analysis protocol with associated reference database and a standardized post-processing step including statistical analysis. Kinematics are collected using a custom-made marker set defined by merging two existing protocols and combine them with a knee alignment device. Following a standing trial, a star-arc hip motion pattern and a set of knee flexion/extension cycles allowing functional, subject-specific calibration of the underlying kinematic model, marker trajectories are acquired for three trials of a set of twelve motor tasks: walking, walking with crossover turn, walking with sidestep turn, stair ascent, stair descent, stair descent with crossover turn, stair descent with sidestep turn, trunk rotations, chair rise, mild squat, deep squat and lunge. This specific set of motor tasks was selected to cover as much as possible common daily life activities. Furthermore, some of these induce greater motion at the knee joint, thus improving the measurement-to-error ratio. Kinetics are acquired by integrating two forceplates in the walkway. Bilateral muscle activity of 8 major muscles is monitored with a 16 channel wireless electromyography (EMG) system. Finally, custom-built software with an associated graphical user interface was created for automated and flexible analysis of gait lab data, including repeatability analysis, analysis of specific kinematic, kinetic and spatiotemporal parameters and statistical comparisons. RESULTS. Following ethical approval and informed consent, the proposed framework was successfully applied in a control group of 80 normal subjects within a wide age-range (age: 54.5Y±19.1; BMI: 25.5±4.0; 40M/40F; 60 Caucasian, 20 Asian) thus constructing the reference database for control. Moreover, the same framework was applied successfully in a randomly selected group of 10 patients with a bi-compartmental knee replacement (BKR) (age: 67.3Y±5.3; BMI: 29.7±3.1; time post-op: 1.65Y±0.4; 2M/8F Caucasian). Comparison between these patients and age-matched controls demonstrates that, for a large range of motor tasks, knee joint kinematics after BKR are as much consistent with the healthy controls (coefficient of multiple correlation (CMC) =0.49) as the consistency within a group of controls or BKR-subjects individually (CMC=0.52). Nevertheless, also significant differences (p<0.0167) were identified which are indicative for retention of pre-operative motion patterns and/or remaining compensations. CONCLUSION. The proposed framework allows in-vivo evaluation of knee joint performance in a standardized, objective and non-invasive way. It is applicable in both healthy subjects and knee replacement patients and is shown to be sufficiently sensitive to detect even relatively small differences between the two populations

Background

Periprosthetic joint infection (PJI) following total knee arthroplasty (TKA) is a severe complication in terms of disability, morbidity, and cost. We performed a study to investigate whether early PJI (within 90 days of primary TKA) is associated with increased mortality. Secondary aims were to compare mortality rates over time and between surgical treatment methods.

Increased incidence of obesity and longer life expectancies will place increased demands on load bearing joints. In the present work, a method of pre-clinical evaluation to assess the condition of the joint and potentially inform on cases of joint deterioration, is described. Acoustic emission (AE) is a non-destructive test methodology that has been used extensively in engineering for condition monitoring of machinery and structures. It is a passive technique that uses piezoelectric sensors to detect energy released from internal structural defects as they deform and grow. The technique has been used with some success in the past to identify characteristic signals generated from the knee joint during activities such as standing and sitting, in candidate arthroplasty patients (1,2). In this study, 40 asymptomatic subjects had AE data generated from their knee joints analysed. Subject characteristics such as age, gender, and lifestyle were disclosed and evaluated against the AE data. Each subject was invited to take a seated position and a piezoelectric AE sensor (Pancom P15, 150kHz resonance, 19mm diameter) was attached to the subject's knee using a wax couplant and tape as close to the articulating surface and on a bony prominence to avoid signal attenuation in the soft tissue. Subjects were invited to sit and stand 3 times. AE data were collected and processed using an AMSY5 AE processor (Vallen, Germany). Tests were repeated on a separate occasion and selected subjects were invited to participate on a third occasion. The AE data of particular interest were the peak amplitudes and the frequency power spectrum of the waveform. Post-test inspection of subject characteristics allowed them to be separated into three broad categories: no previous history (group A), some instances of pain in the knee (group B), and those who have had previous minor surgery on the knee (group C). The corresponding AE results were grouped separately. It was found that groups A and B demonstrated similar signal amplitude characteristics while group C produced much higher, significantly different (p<0.05) amplitudes and amplitude distributions. Typical results are shown in figure 1. At present, broad trends could be identified and relationships emerged between the data and subject history (prior surgery, typical daily activity). Further work will continue with asymptomatic subjects and the work will be extended to pre-operative patients to identify whether certain trends are amplified in this population

Aim

The number of periprosthetic joint infections (PJI) is increasing due to ageing population and increasing numbers of arthroplasty procedures and treatment is costly. Aim of the study was to analyze the direct healthcare costs of PJI in Europe for total hip arthroplasties (THA) and total knee arthroplasties (TKA).

Our objective was to examine revision rates and patient reported outcome scores (PROMS) for cemented and uncemented primary total knee joint replacement (TKJR) at six months, one year and five years post-operatively. Patients and Methods: This matched cohort study involved secondary analyses of data collected as part of a large prospective observational study monitoring outcomes following knee replacement in Christchurch, New Zealand. Cemented and uncemented TKJR participants (n = 1526) were matched on age (± 5 years), sex and body mass index (BMI). From this larger sample, PROMS data, Oxford Knee Score and the Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC), out to five years post-operatively were analysed for a matched subset of participants (n = 252).

The average age of participants was 67.9 years (SD 9.4, range 38-94). There were no differences between cemented and uncemented cohorts on the basis of age, sex, BMI or comorbidities, revision rates or PROMS outcomes. Cemented procedures had greater skin to skin times than uncemented procedures (p < 0.01). Unadjusted outcomes comparing risk for revision across the two participant cohorts did not significantly differ. Overall rates for revision were low (cemented 3.2% v uncemented 2.7%, p=0.70). Propensity adjusted associations between baseline characteristics (age, sex, BMI, comorbidity, baseline Oxford and baseline WOMAC scores) also revealed no differences in risk for revision at any post-operative timepoint.

In this large multi-surgeon matched cohort study there were no significant differences in functional outcomes or revision rates, when outcomes following modern cemented and uncemented TKJR were compared out to 5-year follow up. Based on our findings, uncemented TKJR is predictable irrespective of patient's age, BMI or gender

Abstract

Purpose

Intra-articular corticosteroid injection is widely used for symptomatic relief of knee osteoarthritis. However, if pain is not improved which consequences a total knee arthroplasty (TKA), there is a potential risk of post-operative periprosthetic joint infection (PJI). The aim of this study is to investigate whether the use of preoperative intra-articular corticosteroid injection increases the risk of PJI and to investigate a time frame in which the risk of subsequent infection is significantly increased.

The objective of this study is to introduce the forces acting on the knee joint while ascending from kneeling. Our research group has developed a new type of knee prosthesis which is capable of attaining complete deep knee flexion such as a Japanese style sitting, seiza. Yet we could not set up various kinds of simulation or experiment to assess the performance of our prosthesis because the data about joints' forces during the ascent from deep knee flexion are lacking. Considering this circumstance, we created a 2D mathematical model of lower limb and determined knee joint force during ascent from kneeling to apply them for the assessment of our prosthesis. Ten male and five female healthy subjects participated in the measurement experiment. Although the measurement of subjects' physical parameters was non-invasive and direct, some parameters had to be determined by referring to the literature. The data of ground reaction force and each joint's angle during the motion were collected using a force plate and video recording system respectively. Then the muscle forces and the joints' forces were calculated through our mathematical model. In order to verify the validity of our model approach, we first introduced the data during the activities with small/middle knee flexion such as level walking and rising from a chair; these kinds of data are available in the literature. Then we found our results were in good agreement with the literature data. Next, we introduced the data during the activities with deep knee flexion; double leg ascent [Fig.1 (a)] and single leg ascent [Fig.1 (b)] from kneeling without using the upper limbs. The statistics of the maximum values on the single knee joint for all the subjects were; during double leg ascent, Fmax = 4.6±0.6 (4.3-5.2) [BW: (force on the knee joint)/(body weight)] at knee flexion angle of b =140±8 (134-147)°, during double leg ascent, Fmax = 4.9±0.5 (4.0-5.6) [BW] at b = 62±33 (28-110)° for the dominant leg, and Fmax = 3.0±0.5 (22.2-3.8) [BW] at b = 138±6 (130-150)° for the supporting leg respectively. We found that the moment arm length, i.e., the location of muscle insertion significantly affected the results, while ascending speeds did not affect the results much. We may conclude that the single leg ascent should be recommended since Fmaxdid not become large while deep knee flexion. The values could be used for assessing the strength of our knee prosthesis from the risk analysis view point

The interface condition between the prosthesis and the bone tissue must play important roles during dynamic loading transfer through the knee joint. In this study, the three- dimensional impact finite element (FE) simulations were performed to investigate the impact stress propagation. The FE models of a totally replaced knee joint were constructed with the high shape fidelity. The models included the cortical and cancellous bone, articular cartilage, bone marrow, and the artificial femoral and tibial components. The artificial components were set to the femoral and tibial contact area. The FE meshes had 7251 nodal points and 5547 hexahedral elements (Figure 1). The interfacial condition between the artificial component had two kind of contact situations, bonding situation and no-bonding ones. In the bonding situation, the interface between the artificial components and the cancellous bone had fully fixations. The no-bonding allowed the tie-breaking of each other although the interface had the high coefficient of friction. The three kind of the impact loading (1, 5, and 10kgW) were applied from the proximal femur to the distal side of tibia. In the FE simulations, the impact stress propagated to the tibia through the TKR joint components during several milliseconds. On the interfacial surface at the cancellous side of the proximal tibia, the difference in the stress distribution was observed according to the contact situation of the TKR component (Figure 2). The fully fixation (tied to each other) model showed the high compressive stress on the interface. On the other hand, in the no-bonding model, the compressive stress distributed discontinuously and the high compressive stress was observed only in the hole area and edge of the tibial component during the impact loading. In previous research, the cancellous bone had important roles for the load transmission inside the joint especially under the impact loading condition. However, this study indicated that the stress shielding was caused by the imperfect bonding at the interface. More consideration of the interface situation between the bone and component is required to keep stability for impact loading

Introduction. The low-cost, no-harm conditions associated with vibroarthography, the study of listening to the vibrations and sound patterns of interaction at the human joints, has made this method a promising tool for diagnosing joint pathologies. This current study focuses on the knee joint and aims to synchronize computational models with vibroarthographic signals via a comprehensive graphical user interface (GUI) to find correlations between kinematics, vibration signals, and joint pathologies. This GUI is the first of its kind to synchronize computational models with vibroarthographic signals and gives researchers a new advantage of analyzing kinematics, vibration signals, and pathologies simultaneously in an easy-to-use software environment. Methods. The GUI (Figure 1) has the option to view live or previously captured fluoroscopic videos, the corresponding computational model, and/or the pre- or post-processed vibration signals. Having more than one signal axes available allows for comparison of different filtering techniques to the same signal, or comparison of signals coming from different sensor placements (ex: medial vs. lateral femoral condyle). Using computational models derived using fluoroscopic data synchronized with the vibration signals, the areas of contact between articulating surfaces can be mapped for the in vivo signal (figure 2). This new method gives the opportunity to find correlations between the different sensor signals and contact maps with the diagnosis and cartilage degeneration map, provided by a surgeon, during arthroscopy or TKA implantation (figure 3). Results. Using previously captured data and newly acquired data for subjects from research studies, several different knee pathologies have been analyzed. The signals were listened to audibly after being processed to add a qualitative side. Sounds coming from knees with pathologies revealed noticeable differences compared to the healthy subjects, and the quantitative analysis further supported our hypothesis (>96% accuracy classification patella arthritic subjects vs. healthy). Discussion. Ideally, transitioning towards real-time kinematic tracking with signal acquisition allows for diagnostic screening tools of the knee joint that will provide feedback of cartilage damage maps as well as potential meniscal or ligament injuries. The method used in this study is multi-faceted in that it allows the subject to perform various daily weight or non-weight bearing activities at his/her own speed which makes it easier to use than if the subject had to be in a very controlled environment

It has been proposed that higher knee adduction moments and associated malalignment in subjects with severe medial knee joint osteoarthritis (OA) is due to anatomical deformities as a result of OA [1, 2]. The emergence of patient-matched implants should allow for correction of any existing malalignment. Currently the plans for such surgeries are often based on three dimensional supine computed tomography (CT) scans or magnetic resonance imaging (MRI), which may not be representative of malalignment during functional loading. We investigated differences in frontal plane alignment in control subjects and subjects with severe knee joint OA who had undergone both supine imaging and gait analysis. Fifteen subjects with severe knee OA, affecting either the medial or lateral compartment, and 18 control subjects were selected from a database established as part of a larger study. All subjects had undergone gait analysis using the Vicon motion capture system. OA subjects had undergone routine CT scans and were scheduled for knee joint replacement surgery. Control subjects had no known musculoskeletal conditions and had undergone MRI imaging of hip, knee and ankle joints. Frontal plane knee joint angles were measured from supine imaging (supine) and from motion capture during standing (static) and during gait at the first peak ground reaction force (gait). OA subjects had a significantly higher BMI (p < 0.01) and different gender composition (13 males and 2 females vs 4 males and 5 females; p = 0.03) compared with controls. Multiple linear regression analysis indicated no significant confounding effect of these differences on frontal plane angles measured in supine, static or gait conditions. For both OA and healthy subjects, frontal plane knee angles were significantly higher during gait compared with supine (p = 0.03 and 0.02, respectively). There were also significant differences in knee alignment between OA and healthy subjects for supine and static (p < 0.05) but not for gait, although this was approaching significance (p = 0.052). Overall there seemed to be higher variation in alignment in the OA subjects (Fig. 1). The significantly higher frontal plane knee joint angles measured in both control and OA subjects during gait compared with supine imaging indicate that functional alignment should be taken into consideration when planning patient-specific surgeries. Higher variation in OA patients may be due to alterations in gait patterns due to pain or degree of wear in their osteoarthritic joints, and requires further investigation. In addition, methodological considerations should be taken when comparing alignment from measurements taken with imaging and motion capture to avoid systematic errors in the data. In conclusion, we believe that both supine and loadbearing imaging are insufficient to gain a full representation of functional alignment, and analysis of functional alignment should be routinely performed for optimal surgical planning