Introduction

The National Joint Registry has recently identified failure of large head metal on metal hip replacements. This failure is associated with the high torque at the interface of standard modular taper junction leading to fretting and corrosion. A number of manufacturers produce mini spigots, which in theory, provide a greater range of motion as the neck head junction is reduced. However, the relative torque to interface ratio at this junction is also increased. In this study we investigated hypothesis that the use of small spigots (minispigots) will increase wear and corrosion on modular tapers.

This single incision, anterolateral intermuscular approach (AL-IM) utilises the interval between gluteus medius and tensor fascia lata. The aims of the study were to compare the quality of life, satisfaction and complications of this approach with two of the most commonly used limited incision transmuscular (TM) approaches, namely the mini-posterior (P-TM) and the mini-direct lateral (L-TM).

One hundred and ninety-nine patients receiving MIS THA surgical procedures were evaluated prospectively (63 AL-IM, 68 P-TM and 68 L-TM). The outcome variables were WOMAC function, pain, stiffness, SF-12 (physical & mental), Oxford-12, satisfaction and radiological outcome. Parametric and non-parametric analyses were performed.

There were no significant differences between groups in baseline characteristics including age, sex, BMI, co-morbidity, or pre-op WOMAC, SF-12, Oxford-12 (p> 0.05). However, the AL-IM group was associated with superior outcomes (p< 0.05) in WOMAC function, WOMAC pain, global WOMAC, Oxford-12 and SF-12 physical component.

In the short term the AL-IM approach provides significant improvements in quality of life scores over other limited incision approaches. It provides minimal soft tissue disruption and maintains the abductor musculature and posterior soft tissue envelope, with similar complications and radiological outcomes.

We report the outcomes ten to fifteen years after two stage revision for hip infection in one hundred and three patients.

All patients or their next of kin were contacted to determine their current functional status and whether they had required repeat surgery or had recurrent infection. The Oxford-12, SF-12, and WOMAC questionnaires were administered. A comprehensive chart review was undertaken to review the infective organisms, surgery, approach, complications, and need for further revision surgery.

Ten patients had re-infection, six of whom responded to repeat surgery with no further sequelae. Two patients required resection arthroplasty, one patient underwent hip disarticulation after eventual failure of treatment and bone loss, and one immunocompromised patient developed osteomyelitis and was subsequently lost to follow-up. Long-term success rate for two stage- revision is thus 90.3%, or 96.1% with additional surgery. Since then, three patients required revisions for aseptic loosening, one for recurrent dislocation. We were able to follow up forty-one patients, 85 % of whom provided health-related quality of life outcome scores. Thirty-nine patients were deceased, with their outcome confirmed via their last follow-up or with family members, for a total follow-up rate of 78 %. Twenty-three patients were lost to follow-up, but did not undergo further surgery or have reinfections treated at our centre.

Two-stage revision for hip infection, which includes an interim prosthesis of antibiotic loaded cement, offers a predictable and lasting solution for patients with this difficult problem.

Introduction: To investigate the head/neck interface of total hip replacements and to see whether the use of small spigots (minispigots) results in enhanced wear and corrosion of tapers compared to standard spigots and the influence of the surface finish on this.

Methods: In the total hip replacement combinations the heads were made of cobalt-chrome (CoCr) and the stems of titanium alloy (Ti). Firstly wear and corrosion of minisigots were compared with standard spigots (Test 1) and secondly, these minispigots were compared with another minispigot with a smoother taper surface finish (Test 2). The samples were immersed in aerated Ringers solution (37°C) and loaded for 10 million cycles. The specimens surface parameters and profiles were measured before & after the test. Electrochemical static corrosion tests were carried out on the rough & smooth minispigots from Test 2 where the current was measured with constant potential under loaded and non-loaded conditions. A cyclical sinusoidal load of 1500-200 Newtons for 1000 cycles at ~1 Hz was used. Pitting tests measured the current while increasing and then decreasing the potential of non-loaded and loaded specimens. Two newly manufactured rough and smooth minispigots were subjected to the same electrochemical corrosion tests.

Results: In Test 1 the results demonstrated that pre-test the surfaces of the female tapers were similar for all heads. Post-testing the Ra values on the female tapers had become greater for the minispigots compared with standard spigots. An abrupt change was noted on the surface profile of the female taper where it was in contact with the male Ti taper, indicating the the CoCr head had corroded. The Ti male tapers were unchanged. Scanning electron microscopy showed that the coarser profile in the corroded region of the CoCr was similar to the profile on the Ti male taper. Pitting corrosion was evident in the grooves on the CoCr. In Test 2 the smooth spigots were not affected, but in the rough minispigots, Ra values had increased in the female tapers. Static corrosion tests showed evidence of fretting in the rough but not the smooth minispigots. When comparing new rough & smooth minispigots, static corrosion testing with clyclical loading showed that for minispigots with a rough finish the current fluctuated with each cycle. Pitting scans showed a greater hysteresis with the rough minispigot compared with the smooth minispigot indicating potentially greater corrosion in the former.

Conclusion: The cobalt-chrome/titanium alloy combinations where the surface finish on the male taper was coarse, corrosion was increased in minispigots compared with standard spigots. This was due to the smaller area of contact of the minispigot at the interface. This corrosion appears to be mediated through the mechanism of fretting corrosion. Surface finish was crucial and corrosion of the minispigot was reduced if the surface finish was smooth. Manufacturers should investigate the effect of surface finish on the corrosion of their tapers particularly where cobalt-chrome/titanium alloy combinations are used.

Introduction: The management of severe slipped upper femoral epiphysis (SUFE) is controversial. Many types of operation have been advocated. The cuneiform osteotomy offers the potential to restore normal anatomy and hence reduce the development of osteoarthritis, but it is not without its risks. This aim of this study was to quantify the long-term clinical & radiological results of Fish’s cuneiform osteotomy at skeletal maturity.

Method: Twenty-seven patients underwent a cuneiform osteotomy between 1990 – 2003. Two patients were lost to follow-up. Therefore 25 hips in 24 patients were reviewed at a mean follow-up of 8 years and 3 months. The mean slip angle was 77 ± 13 degrees and all were categorized as unstable. Sex distribution was equal and the average age at follow-up was 21.5 years (range 14 – 31 years). The Iowa hip-rating, Harris Hip Score and radiographic classification of degenerative joint disease according to Boyer et al.,¹ were determined at follow-up.

Results: The mean Iowa hip-rating at follow-up was 93.7 ± 7.7 with a mean range of motion score of 8.1 ± 1.8. The Harris Hip Score was 95.6 ± 5.9. Nineteen patients were classified as Grade 0 on Boyer’s radiographic assessment, four Grade 1 and two Grade 2. Correction to neutral ± 10 degrees was achieved in all patients. The rate of avascular necrosis was 12 % and chondrolysis 16 %.

Discussion: Cuneiform osteotomy for severe SUFE is a valid treatment option and complication rates were no higher than other operative interventions reported in the literature. Patients enjoyed an excellent range of motion and were extremely satisfied with the outcome. The restoration of anatomy equates to better function and possibly the delay in onset of osteoarthritis.

Aims: To investigate whether the use of mini-spigots result in enhanced wear and corrosion of tapers compared to standard spigots and the influence of the surface finish on this. Methods: The heads were cobalt chrome and the stems titanium alloy. Firstly wear and corrosion of standard spigots were compared with mini-spigots and secondly, these mini-spigots with another mini-spigot with a smoother surface finish. The samples were immersed in aerated Ringers solution (37°C) and loaded for 10 million cycles. Then samples were sectioned and the surface parameters measured and interfaces investigated using scanning electron microscopy. Static corrosion tests were used under loaded and non-loaded conditions and pitting tests for non-loaded samples. Results: Pre-experimentation the surfaces of the female tapers were similar for all heads. At the end of the first test the surface parameters on the female tapers had become significantly greater (p=0.034) for the mini-spigots compared with standard spigots and an abrupt change noted on the surface profile of the female taper where it contacted the male taper, indicating that the cobalt chrome head had corroded. Scanning electron microscopy showed that the coarser profile in the corroded region of the cobalt chrome head was similar to the profile on the titanium stem taper. Pitting corrosion was evident in the grooves on the cobalt chrome. The smooth mini-spigots were less affected. Conclusions: In cobalt chrome- titanium alloy combinations where the surface finish on the taper is coarse, corrosion is increased on a mini spigot compared with standard spigot. Surface finish is crucial and corrosion of the mini spigot is reduced if the surface finish is smooth.