Total knee arthroplasty has become an established operation. Cemented fixation of the components has given satisfactory results and is accepted as the gold standard. Cement failure with aseptic loosening, however, is a possible long term complication. This is particularly important in view of the increasing number of younger patients who can benefit from this procedure. Hence the attraction of using implants fixed by direct osseointegration of bone into the implant, by passing the potential weak link of the cement. The objective of this study was to determine the mid-term clinical, radiological and functional outcomes after navigated cementless and cemented implantation of total knee arthroplasties without patella resurfacing done by a single surgeon.Introduction
Objectives
Wolff's Law proposes that trabecular bone adapts in response to mechanical loading and that trabeculae align with the trajectory of predominant loads. The current study is aimed to investigate trabecular orientation in the tibia in patients with osteoarthritis of the knee. Consistent with Wolff's Law, it was hypothesised that orientation would reflect the mechanical loading of the joint and hence that there would be a correlation between the trabecular orientation and the mechanical axis of the lower limb. 51 anonymised radiographs from patients with osteoarthritis were analysed using ImageJ (National Institute of Health). Each patient had both a standard anteroposterior radiograph of the knee and a long leg view taken while weight bearing. For each anteroposterior radiograph, the angle of the femoral shaft and tibial shaft were measured. The femoral shaft – tibial shaft (FS -TS) angle was then calculated as the difference between the two, as described by Sheehy et al. (2011). A medial rectangle was selected with the top, bottom, medial and lateral borders being the sclerotic bone, the growth line, the bone edge and the centre of the medial tibial spine. Corresponding measurements were done on the lateral side. Trabecular orientation of both areas was measured using OrientationJ (an ImageJ plugin). In all cases the medial and lateral orientation angles were expressed relative to the angle of the tibial shaft. The mechanical axis of the lower limb was measured from the full length radiographs by calculating the angle formed by the femoral and tibial axes, as described by Goker and Block. All measurements were done independently by two observers, SAS and SL.Introduction
Methods
Recent publications have supported the anatomic placement of anterior cruciate grafts to optimise knee function. However, anatomic placement using the anteromedial portal has been shown to have a higher failure rate than traditional graft placement using the transtibial method. This is possibly due to it being more technically difficult and to the short femoral tunnel compromising fixation methods. It also requires the knee to be in hyper flexion. This position is not feasible during with a tourniquet in situ on the heavily muscled thighs of some athletes. Hypothesis: That navigation can be used to place the femoral tunnel in the anatomic position via a more medial transtibial tunnel. 25 patients underwent Navigated Anterior Cruciate reconstruction with quadruple hamstring grafts. The Orthopilot™ 3.0 ACL (BBraun Aesculap, Tuttlingen) software was used. The femoral and tibial ACL footprints were marked on the bones with a radio frequency probe and registered. The pivot shift test, anterior drawer and internal and external rotation were registered. A navigated tibial guide wire was inserted at 25° to the sagittal plane and 45° to the transverse plane exiting through the centre of the tibial footprint. The guide wire was advanced into the joint to just clear of the surface of the femoral footprint with the knee in 90° flexion. Flexion/extension of the knee was done to determine the closest position of the guide wire tip to the centre of the anatomical femoral footprint. If the tip was within 2mm of the centre of footprint, the position was accepted. If not the tibial guide wire was repositioned and the process repeated. The tibial tunnel was drilled, followed by transtibial drilling of the femoral tunnel. A screen shot was done to allow determination of the shape and area of the tunnel aperture relative to the femoral footprint using ImageJ (National Institute of Health). The graft was fixed proximally with an Arthrex ACL Tightrope® and distally with a Genesys™ interference screw. The pivot shift test, anterior drawer and internal and external rotation were repeated and recorded using the software.Background
Methods
