Introduction: Cementless cup designs in metal-on-metal (MoM) hip resurfacing devices generally depend on a good primary press-fit fixation which stabilises the components in the early post-operative period. Pressfitting the cup into the acetabulum generates non-uniform compressive stresses on the cup and consequently causes non-uniform cup deformation. That in turn may result in equatorial contact, high frictional torque and femoral head seizure. It has been reported that high frictional torque has the potential to generate micromotion between the implant and its surrounding bone and as a result adversely affect the longevity of the implant. The aim of this study was to investigate the effects of cup deformation on friction between the articulating surfaces in MoM bearings with various clearances. Materials and methods: Six Birmingham Hip Resurfacing (BHR) devices with various clearances (80 to 306 μm) were tested in a hip friction simulator to determine the friction between the bearing surfaces. The components were tested in clotted blood which is the primary lubricant during the early post-operative period. The joints were friction tested initially in their pristine conditions and subsequently the cups were deflected by 25– 35 μm using two points pinching action before further friction tests were carried out. Results and Discussions: It has been reported that reduced clearance results in reduced friction. However, none of the previous studies have taken cup deflection into consideration nor have they used physiologically relevant lubricant. The results presented in this study show that for the reduced clearance components, friction was significantly increased when the cups were deflected by only 30 μm. However, for the components with higher clearance the friction did not change before and after deflection. It is postulated that the larger clearances can accommodate for the amount of distortion introduced to the cups in this study

Introduction: In vitro studies have shown that low clearance bearings have the potential to generate low wear. However, cementless acetabular cups are designed to be press fitted into the acetabulum, which could generate compressive stresses and non-uniform cup deformation during implantation. Deformation of the low clearance acetabular cups could also potentially lead to clamping or seizure of the joints and high frictional torque leading to implant failure. To obtain the benefit of low clearance and low wear, without compromising the tribological performance of the cup, a deflection compensation (DefCom) cup was designed. DefCom offers the benefits of low wear associated with low clearance components whilst reducing the risk of component seizure and high frictional torque due to component deformation. Aim: The study was conducted in order to evaluate the tribological performance of a DefCom acetabular cup. Materials and Methods: 50 mm diameter metal-on-metal DefCom hip resurfacing cups were used in this study. The components had an average clearance of 105±3 μm at the articulating sphere. Three of the cups were deformed plastically, along the ilial-ischeal column of the acetabulum. The degree of deformation was measured using the coordinate measuring machine, measuring the change in diameter of the cup in the direction of deformation. The cups were deformed on average by 65μm. The devices were tested in a ProSim hip wear Simulator for 5 million cycles. The lubricant was new born calf serum with 0.2% sodium azide diluted with de-ionised water to achieve protein concentration of 20 mg/ml. The flexion/extension was 30° and 15° with an internal/external rotation of ±10°. The force was Paul-type stance phase loading with a maximum load of 3 kN and a swing phase load of 0.3 kN, conducted at 1 Hz. Results: The DefCom and deformed DefCom components showed a similar bi-phasic wear pattern to that of the BHR devices. Showing a period of ‘running in’ wear up to 1 Mc and then a reduced wear rate during the steady state phase from 1 Mc onwards. The DefCom devices produced a wear rate of 0.24 mm3/Mc, whilst the deformed DefCom joints produced a wear rate of 0.48 mm3/Mc for the running-in phase. Steady state wear was achieved for all joints after 1 Mc. The average steady state wear (1.0–5.0 Mc) rate for the DefCom joints was 0.12 mm3/Mc, with 0.14 mm3/Mc for the deformed joints joint. The wear rate for the non-deformed DefCom device is lower than that generated by the BHR, which were 0.72 mm3/Mc and 0.18 mm3/Mc for the running-in and steady state wear, respectively. Conclusion: The study has shown that the DefCom acetabular cup has the potential to reduce the initial running-in wear by reducing the clearance at the contact area between the head and cup, whilst compensating for deformation that may occur during cup implantation

Introduction. In vitro studies have shown that low clearance metal-on-metal hip joints have the potential of reducing wear during the running-in phase [1]. However, cementless acetabular cup relies on press fitting into the acetabulum, which can generate non-uniform compressive stresses and non-uniform in vivo cup deformation [2, 3]. This could then lead to equatorial contact, resulting in higher wear and friction for a MoM bearing with low clearance. To benefit from low wear generated by low clearance and at the same time to avoid the potential of head seizure and high frictional torque caused by cup deformation, a deflection compensation acetabular cup (DefCom) has been developed based on the Birmingham Hip Resurfacing (BHR) device. The articulating sphere of the DefCom cup provides a low clearance bearing area, whilst the non-articulating sphere maintains the standard BHR clearance. The aim of this study was to evaluate the wear performance of the novel DefCom hip joint using a hip wear simulator. Materials and Methods. Five pairs of 50 mm DefCom devices were tested in a ProSim hip wear Simulator for 5 million cycles (MC) at a frequency of 1 Hz. The lubricant was new born calf serum with 0.2% sodium azide diluted with de-ionised water to achieve protein concentration of 20 mg/ml. The flexion/extension was 30° and 15° and the internal/external rotation was 10°. The force was Paul-type stance phase loading with a maximum load of 3 kN and a standard ISO swing phase load of 0.3 kN. Five standard 50 mm BHR devices were tested under the same testing conditions for comparison. Statistical analyses were performed at a 95% confidence level (CL) using the statistics function in Excel (Microsoft(r) Excel 2003). Results. Fig. 1 shows the cumulative volume loss against number of wear cycles for the DefCom and the BHR devices. Similar to the BHR device, the DefCom joints experienced relatively higher amount of material loss during the running-in phase from 0 to 1.0 Mc. However, the running-in wear rate for the DefCom device (0.23 ± 0.06 mm. 3. /MC) was much lower than that for the BHR device (0.72 ± 0.15 mm. 3. /MC). Steady state wear was achieved for all the joints from 1.0 to 5.0 MC. The steady state wear rate was 0.11 ± 0.03 mm. 3. /MC for DefCom and 0.18 ± 0.01 mm. 3. /MC for the BHR joints. Discussion. This study has shown that the DefCom acetabular cup has the potential to reduce the initial running-in wear by reducing the clearance at the contact area between the head and cup. The device also has the potential to avoid deformation induced head seizure and high frictional torque by maintaining a larger clearance at the periphery of the cup

Background

Surgical reconstruction of the anterior cruciate ligament is a common practice to treat the disability or chronic instability of the knee. Several factors associated with success or failure of the ACL reconstruction, including surgical technique and graft material and graft tension. We aimed to show how we can optimize the graft properties and achieve better post surgical outcomes during ACL reconstruction using 3-dimensional computational finite element simulation.

The surgical treatment of typical pathological conditions of the knee combined with deflections along the sagittal axis is complex, especially when the angles of such deflections are considerable in size. Prior to treatment, the first problem concerns detecting the origin of the deflection, whether it is osseous, ligamentous or mixed, especially in cases of knee recurvation. The possibility of finding patients with what is known as “prophylactic” correction of the deflection is very rare. Orthopaedic surgeons may encounter some cases in which deformation along the sagittal axis represents the primum movens of the pathology and others in which this deflection represents a further problem in curing the condition. The different situations may require the following different treatments: (a) Correction of the deflection; (b) correction of the deflection and the pathological condition; and (c) correction of the pathological condition and not the deflection. We believe that, in the most serious cases, the deflection must be corrected and then meticulous pre-operative preparation is required. However, in order to select the most appropriate treatment, it is essential, in our opinion, to determine the cause of the deflection along the sagittal axis. In our experience, the treatment of pathological conditions of the knee such as ligamentous reconstruction, knee arthroplasty and corrective osteotomies combined with deflection along the sagittal axis increase the difficulties of surgery, especially in cases of relevant knee recurvation, both osseous and ligamentous

Introduction. During its conception, Ilizarov advocated a fine wire tension of between 900N and 1200N for circular frame construction. Wire tension can be achieved via a tensioning device or ‘Russian tensioning’ (a fixed wire lengthening around a bolt). There is limited information on the latter technique. This study aimed to explore the tensions achieved via Russian tensioning and report the impact of a second wire on construct tension. Materials and Methods. A single 160mm stainless-steel ring was constructed, then 1.8mm stainless steel wires secured using a Russian fixation bolt and Russian tensioned with a 2nd bolt. The angle subtended by tensioning using the 2nd bolt was measured using a goniometer. Angles of 45°, 70° and 90° were repeated in triplicates, with wire tension measured using a calibrated tensiometer. A 2nd orthogonal wire was placed on the opposite side and tensioned to the same angle. Tensions of both wires were remeasured and recorded. Statistical comparison using unpaired t-tests was used to compare mean tensions. A value of p<0.05 was considered significant. Results. Russian wire tensioning at all angles was insufficient to achieve the target range of 900–1200N (range 99–110N). The addition of a second orthogonal wire changed frame dynamics such that a 90° angle resulted in both wires achieving adequate tension (mean 1143N, SD 307N). Increases were significant across all tensioning angles (p–<0.002) however only biomechanically relevant for 90°. Conclusions. Russian tensioning is insufficient with a single wire, however the addition of an orthogonal wire increases tension in both wires, which reaches the target range at 90° deflection. This phenomenon is explained by force transmission initially into ring deflection, which is then balanced out by the second wire. Further study of this phenomenon using wire tensioners is warranted, and also the impact of non-orthogonal wire constructs

Introduction. Transosseous flexion-distraction injuries of the spine typically require surgical intervention by stabilizing the fractured vertebra during healing with a pedicle-screw-rod constructs. As healing is taking place the load shifts from the implant back to the spine. Monitoring the load-induced deflection of the rods over time would allow quantifiable postoperative assessment of healing progress without the need for radiation exposure or frequent hospital visits. This approach, previously demonstrated to be effective in assessing fracture healing in long bones and monitoring posterolateral spinal fusion in sheep, is now being investigated for its potential in evaluating lumbar vertebra transosseous fracture healing. Method. Six human cadaveric spines were instrumented with pedicle-screws and rods spanning L3 vertebra. The spine was loaded in Flexion-Extension (FE), Lateral-Bending (LB) and Axial-Rotation (AR) with an intact L3 vertebra (representing a healed vertebra) and after transosseous disruption, creating an AO type B1 fracture. The implant load on the rod was measured using an implantable strain sensor (Monitor) on one rod and on the contralateral rod by a strain gauge to validate the Monitor's measurements. In parallel the range of motion (ROM) was assessed. Result. The ROM increased significantly in all directions in the fractured model (p≤0.049). The Monitor measured a significant increase in implant load in FE (p=0.002) and LB (p=0.045), however, not in AR. The strain gauge detected an increased implant load not only in FE (p=0.001) and LB (p=0.016), but also in AR (p=0.047). The highest strain signal was found during LB for both, the Monitor, and the strain gauge. Conclusion. After a complete transosseous disruption of L3 vertebra the load on the implants was significantly higher than in the intact respectively healed state. Innovative implantable sensors could be used to monitor those changes allowing the assessment of healing progression based on quantifiable data rather than CT-imaging

Extracellular matrix (ECM) mechanical cues guide healing in tendons. Yet, the molecular mechanisms orchestrating the healing processes remain elusive. Appropriate tissue tension is essential for tendon homeostasis and tissue health. By mapping the attainment of tensional homeostasis, we aim to understand how ECM tension regulates healing. We hypothesize that diseased tendon returns to homeostasis only after the cells reach a mechanically gated exit from wound healing. We engineered a 3D mechano-culture system to create tendon-like constructs by embedding patient-derived tendon cells into a collagen I hydrogel. Casting the hydrogel between posts anchored in silicone allowed adjusting the post stiffness. Under this static mechanical stimulation, cells remodel the (unorganized) collagen representing wound healing mechanisms. We quantified tissue-level forces using post deflection measurements. Secreted ECM was visualized by metabolic labelling with non-canonical amino acids, click chemistry and confocal microscopy. We blocked cell-mediated actin-myosin contractility using a ROCK inhibitor (Y27632) to explore the involvement of the Rho/ROCK pathway in tension regulation. Tissue tension forces reached the same homeostatic level at day 21 independent of post compliance (p = 0.9456). While minimal matrix was synthesized in early phases of tissue formation (d3-d5), cell-deposited ECM was present in later stages (d7-d9). More ECM was deposited by tendon constructs cultured on compliant (1Nm) compared to rigid posts (p = 0.0017). Matrix synthesized by constructs cultured on compliant posts was less aligned (greater fiber dispersion, p = 0.0021). ROCK inhibition significantly decreased tissue-level tensional forces (p < 0.0001). Our results indicate that tendon cells balance matrix remodeling and synthesis during tissue repair to reach an intrinsically defined “mechanostat setpoint” guiding tension-mediated exit from wound healing towards homeostasis. We are identifying specific molecular mechanosensors governing tension-regulated healing in tendon and investigate the Rho/ROCK system as their possible downstream pathway

Objectives: To develop a non-invasive method to assess the wire tension quantitatively which can be used in clinic. Background: Fine-wire external fixators are widely used in the fixation of fractures and limb reconstruction. A requirement of stable fixation is that the wires maintain their tension. Recent lab tests have shown that substantial reduction in wire tension occurred during the simulated operative procedures. Clinical experience also indicated that wire site discomfort might be related to loss in wire tension. It would be very helpful if the wire tension could be assessed quantitatively by a non-invasive method. Methods: An apparatus based on a LVDT (Linear Variable Differential Transformer) was developed to apply a constant transverse force to a wire and measure its deflection with respect to another parallel wire. An unstable oblique fracture was created in a Sawbones tibia and stabilized by a Sheffield Ring Fixator. The deflection of the testing wire was measured in four tests: (1) Two parallel wires fixation, tensioned reference wire, variable clamp to bone distance; (2) Two parallel wires fixation, loose reference wire, 80mm clamp-bone distance. (3) Two groups of parallel wires fixation with 70° crossing angle, tensioned reference wire, 80mm clamp-bone distance; (4) Two groups of parallel wires fixation with 70° crossing angle, tensioned reference wire, 80mm clamp-bone distance, osteotomy site fixed with a lag screw to simulate a stable fracture or a healing fracture. Fracture stiffness in the above conditions was derived from previous work. Stepwise multiple variable regression analyses were performed to determine the relationship between wire deflection and wire tension, clamp-bone distance, number of wires, reference wire tension, and fracture stiffness. Results: The reference wire tension and fracture stiffness was excluded from the regression equation, indicating that they did not affect the wire deflection. The regression equation containing only the testing wire tension had an adjusted R-square value of 0.521, while the equation containing the testing wire tension and clamp-bone distance had the R-square values of 0.854. The addition of the number of wires to the regression equation resulted in a slight increase of the R-square value (0.862). Conclusion: The wire deflection and the clamp-bone distance are the two most important factors that affect wire deflection. The measurement of wire deflection has the potential to predict wire tension and the effect of clamp-bone distance must be considered. Further work is required to refine the apparatus for clinical use

Introduction The success of spinal fusion is widely accepted. However, room for improvement is possible as complication rates remain between 5%–10% due to tears, device migration, improper sizing and lead to pseudoarthroses. 1. In an attempt to improve outcomes, an expanding intervertebral cage that can be adjusted inter-operatively for proper segmental distraction and support has been designed and undergone preliminary evaluations. Materials and Methods The main features of the device include a locking spacer that is rotated into position providing both proper distraction and stability based on clinical need. All of the rotating spacers associated with the device possess equivalent minor diameters with distraction height achieved by varying major diameters. Once the appropriate spacer has been identified, a locking mechanism is engaged, locking the spacer in place. In order to ensure parallel distraction while retaining segmental lordosis, the baseplates encompass a variety of angles and are guided bilaterally during distraction. To evaluate this design, a finite element model (Solidworks, Cosmos, Concord, MA) was employed on a 12° lordosed, 18mm distraction height device under a compressive load of 2745N. This represents the least stable condition as the lordosis angle and height are at the maximum values clinically appropriate. Static and dynamic mechanical testing were performed. Static testing consisted of applying at compressive load at 25mm/min (858 Mini Bionix, MTS, Eden Prairie, MN) until failure of the device or a maximum load of 7000N was sustained. Maximum load, device stiffness and overall deformation were extracted from the load versus deflection data. Dynamic testing (ELF 3300, Bose, Minnetonka, MN) involved sinusoidal loading from −50N to −300N at a rate of 60Hz. This load represents the approximate mass of the torso. The device was cycled for 5 million cycles with load and displacement data acquired at 250,000 cycle intervals at a rate of 500Hz. Net deflection was computed at 250,000 cycle intervals while compressive stiffness was computed at 500,000 cycle intervals. Non-linear regression analyses were performed for both deflection and stiffness versus cycle number in order to elucidate the behavior of the device. Results and Discussion: Finite element analysis revealed a maximum stress level of 163MPa equatings to a safely factor of 6.5 in the case of titanium alloy. Static testing revealed that when fully distracted, the device sustained a compressive load in excess of 7160N and displayed a compressive stiffness over 28500N/mm. It has been reported that the vertebral body will fail at levels below 5000N.[. 2. ] With respect to fatigue testing, the device achieved the required 5 million cycles. Non-linear analysis of the deformation data (R2> 0.78) displayed a net deflection change of 0.041mm with a subsidence rate of 0.3mm/million cycles. Compressive stiffness (R2> 0.99) was altered at a rate of 0.36N/mm/million cycles. These results confirm that this novel design can enhance the likelihood for osseointegration by maintaining the micromotion levels below the reported critical value of 75μm.[. 3. ]. Conclusions: The design of novel expanding and interoperatively adjustable intervertebral spacer has been realized and appears viable based on preliminary mechanical and finite element analysis

Gavril Ilizarov advocated a fine wire tension of between 900N and 1200N for circular frame construction. Wire tension can be achieved via a tensioning device or ‘Russian tensioning’ (a fixed wire lengthening around a bolt). There is limited information on the latter technique. This study explored the tensions achieved via Russian tensioning and reports the impact of a second wire on construct tension. A single 160mm stainless-steel ring was constructed, then 1.8mm stainless steel wires were secured using a Russian fixation bolt and Russian tensioned with a 2nd bolt. The angle subtended by tensioning using the 2nd bolt was measured using a goniometer. Angles of 45°, 70° and 90° were repeated in triplicates, with wire tension measured using a calibrated tensiometer. A second, orthogonal wire was added and tensioned to the same angle. Tensions of both wires were remeasured and recorded. Unpaired t-tests were used to compare mean tensions. A value of p<0.05 was considered significant. Tensioning at all angles was insufficient to achieve the target range of 900–1200N (range 99–110N). A second, orthogonal wire changed frame dynamics such that a 90° angle resulted in both wires achieving adequate tension (mean 1143N, SD 307N). Increases were significant across all tensioning angles (p=<0.002) however only biomechanically relevant for 90°. Russian tensioning is insufficient with a single wire, however the addition of an orthogonal wire increases tension in both wires, reaching the target range at 90° deflection. Further study using wire tensioners is warranted, and also the impact of non-orthogonal wire constructs

Introduction. A clinical case of catastrophic ring failure in a 13 year old autistic overweight patient during treatment for tibial lengthening and deformity using a Taylor Spatial Frame is reported. Ring failure was noted during the later stages of bone healing and the frame was removed. The clinical outcome was not affected by the catastrophic ring failure. The photograph of the deformed ring is presented below:. Materials and Methods. The patient's notes and X-rays were reviewed and a macroscopic examination of the deformed ring was performed. Mechanical tests of different Taylor Spatial frame constructs were performed in an attempt to simulate the deformity that was clinically observed. Different constructs of TSF of different ring sizes were fixed to polyurethane cylinders simulating bone, were mechanically tested to failure and load/deflection curves were produced. Results. Macroscopically the ring looked otherwise normal. Gradual mechanical compression tests of Taylor Spatial frame constructs showed that ring deformation increased by increasing the ring diameter and by using jointed rather than full joints without a ring. The ring deformation observed clinically was reproduced at the lab by applying high loads on frame constructs composed of large diameter jointed rings not rigidly fixed to bone. Conclusions. Taylor Spatial frame ring failure during treatment is a serious complication that has not been described in the literature. Possible causes are discussed. Clinicians are advised to use the smaller possible diameter rings. Where large diameter rings are required, these rings should preferably be not jointed. Half rings when used should be carefully and securely joined together by the operating surgeon in order to make a complete ring. For any figures or tables, please contact the authors directly

This study was to evaluate the stability of a delta keel tibial tray using a block prosthesis and to determine whether a long intramedullary stem is a necessary adjunct to augment construct stability. An experimental technique was used employing strain gauges and deflection transducers to assess the stiffness and principle strains conferred to human cadaveric tibiae under various axial loading conditions. As a control measure, tests were conducted in the absence of any bone loss, and repeated in a simulated bone defect treated with a metal block. The latter was analysed with and without augmentation of the tibial tray with an intramedullary stem. With axial loading of 2000N, the tray and block configuration resulted in 21% less proximal bone strain than the tray alone. The combined tray, block and stem resulted in 35% less proximal bone strain than the tray alone. Using the tray and block produced 1.06 times more deflection of the tibial tray and using the tray, block and stem 1.03 times more deflection of the tibial tray than the tray alone in the absence of a bony defect. There was no statistical difference in overall construct stability (p < 0.05) despite the large strain-offsetting effect recorded using the tibial tray in conjunction with the block and stem. These results suggest that isolated bone defects that can be dealt with using a single block and modern standard tibial tray may not require additional supplementation with a long intramedullary stem

Despite being demonstrably better than conventional surgical techniques with regards to implant alignment and outlier reduction, computer navigation systems have not faced widespread adoption in surgical operating rooms. We believe that one of the reasons for the low uptake stems from the bulky design of the optical tracker assemblies. These trackers must be rigidly fixed to a patient's bone and they occupy a significant portion of the surgical workspace, which makes them difficult to use. In this study we introduce the design for a new optical tracker system, and subsequently we evaluate the tracker's performance. The novel tracker consists of a set of low-profile flexible pins that can be placed into a rigid body and individually deflect without greatly affecting the pose estimation. By relying on a pin's stiff axial direction while neglecting lateral deviations, we can gain sufficient constraint over the underlying body. We used an unscented Kalman filter based algorithm as a recursive body pose estimator that can account for relative marker displacements. We assessed our tracker's performance through a series of simulations and experiments inspired by a total knee arthroplasty. We found that the flexible tracker performs comparably to conventional trackers with regards to accuracy and precision, with tracking errors under 0.3mm for typical operating conditions. The tracking error remained below 0.5mm during pin deflections of up to 40mm. Our algorithm ran at computation speeds greater than real-time at 30Hz which means that it would be suitable for use in real-time applications. We conclude that this flexible pin concept provides sufficient accuracy to be used as a replacement for rigid trackers in applications where its lower profile, its reduced invasiveness and its robustness to deflection are desirable characteristics

Total shoulder arthroplasty (TSA) is an effective treatment for end-stage glenohumeral arthritis. The use of high modulus uncemented stems causes stress shielding and induces bone resorption of up to 63% of patients following TSA. Shorter length stems with smaller overall dimensions have been studied to reduce stress shielding, however the effect of humeral short stem varus-valgus positioning on bone stress is not known. The purpose of this study was to quantify the effect of humeral short stem varus-valgus angulation on bone stresses after TSA. Three dimensional models of eight male cadaveric humeri (mean±SD age:68±6 years) were created from computed tomography data using MIMICS (Materialise, Belgium). Separate cortical and trabecular bone sections were created, and the resulting bone models were virtually reconstructed three times by an orthopaedic surgeon using an optimally sized short stem humeral implant (Exactech Preserve) that was placed directly in the center of the humeral canal (STD), as well as rotated varus (VAR) or valgus (VAL) until it was contacting the cortex. Bone was meshed using a custom technique which produced identical bone meshes permitting the direct element-to-element comparison of bone stress. Cortical bone was assigned an elastic modulus of 20 GPa and a Poisson's ratio of 0.3. Trabecular bone was assigned varying stiffness based on CT attenuation. A joint reaction force was then applied to the intact and reconstructed humeri representing 45˚ and 75˚ of abduction. Changes in bone stress, as well as the expected bone response based on change in strain energy density was then compared between the intact and reconstructed states for all implant positions. Both varus and valgus positioning of the humeral stem altered both the cortical and trabecular bone stresses from the intact states. Valgus positioning had the greatest negative effect in the lateral quadrant for both cortical and trabecular bone, producing greater stress shielding than both the standard and varus positioned implant. Overall, the varus and standard positions produced values that most closely mimicked the intact state. Surprisingly, valgus positioning produced large amounts of stress shielding in the lateral cortex at both 45˚ and 75˚ of abduction but resulted in a slight decrease in stress shielding in the medial quadrant directly beneath the humeral resection plane. This might have been a result of direct contact between the distal end of the implant and the medial cortex under loading which permitted load transfer, and therefore load-reduction of the lateral cortex during abduction. Conversely, when the implant was placed in the varus angulation, noticeable departures in stress shielding and changes in bones stress were not observed when compared to the optimal STD position. Interestingly, for the varus positioned implant, the deflection of the humerus under load eliminated the distal stem-cortex contact, hence preventing distal load transfer thus precluding the transfer of load

Aim. We evaluated the effect of the intact periosteum on the biomechanical properties of the rat long bones. Materials-Methods. The biomechanical properties of both femora and tibiae of 30 male, 4-month old Wistar rats have been evaluated in three-point bending testing. In one bone of each pair of femora or tibiae the periosteum was preserved intact, while in the contra-lateral bone the periosteum was stripped off. Ultimate strength,stiffness,energy absorption and deflection were derived automatically from the load-deformation curve recorded for each bone. Results. As regards the femur, the periosteum-covered bones displayed statistically significant higher values for all parameters measured compared to the periosteum-stripped bones. In the tibia, only energy absorption and deflection were significantly higher in the periosteum-covered bones. The fracture pattern was also different in these two groups. The periosteum-stripped femora and tibiae failed catastrophically, while in the periosteum-covered bones the two bone parts remained in close apposition stabilized by the periosteal membrane. Conclusion. The periosteum exacerbates the biomechanical capacity of intact rat long bones examined in bending, probably taking advantage of its fibrous composition and elastic properties

Trabecular bone is a multiscale hierarchical composite material that is known to display time-dependant properties. However, most biomechanical models treat this material as time independent. Time-dependant properties, such as creep and relaxation, are thought to play an important role in many clinically relevant orthopaedic issues: implant loosening, vertebral collapse, and non-traumatic fractures. In this study compressive multiple-load-creep-unload-recovery (MLCUR) tests were applied to human trabecular bone specimens. 15 female femoral heads were harvested, with full ethical approval and patient consent, at the time of total hip replacement. Central cores were extracted and cut parallel under constant irrigation. Specimens were embedded in end caps using surgical cement, an epoxy tube was secured around the end caps and filled with phosphate buffered saline (PBS) to ensure the specimens remained hydrated throughout. Embedded samples were scanned by microCT (SkyScan 1172, Bruker) at a resolution of 17µm to determine microarchitecture. Bone volume fraction (BVF) was used to represent microarchitecture. Specimens had an effective length of 16.37mm (±1.90SD) with diameter of 8.08mm (±0.05SD), and BVF of 19.22% (±5.61SD). The compressive MLCUR tests were conducted at 5 strain levels, 2000µε, 4000µε, 6000µε, 8000µε and 10000µε. At each strain level, the load required to maintain each strain was held for 200s (creep) then unloaded to 1N for 600s (recovery). The instantaneous, creep, unloading and recovered strains can be easily obtained from the strain-time curves. Stress-strain plots revealed the Young's modulus. Data was modelled using line of best fit with appropriate curve fitting. R2 values were used to indicate association. Mechanical testing demonstrated the expected time independent relationship between BVF and stiffness: higher stiffness was found for specimen with higher BVF and this was consistent for all strain levels. Creep strain was found to depend on instantaneous strain and BVF. At low levels of instantaneous strain, there was a greater amount of creep strain in low BVF samples (R2 = 0.524). This relationship was no longer apparent at higher strain levels (R2 = 0.058). Residual strain also depended on the applied instantaneous strain and BVF: at low levels of strain, residual strain was similar with all BVF (R2 = 0.108) and at high levels of strain, residual strain was greater in low BVF samples (R2 = 0.319). The amount of instantaneous strain applied to each sample is constant, variations in stiffness result in different applied loads. In low BVF bone, the stiffness is also low, therefore the stress required to reach designed strain is also lower: yet, there is more creep and less recovery. We have demonstrated that even at loads below recognised yield levels, time-dependence affects the mechanical response and residual strain is present. In cases of low BVF, deflection due to creep, and increased irrecoverable strain could have clinically relevant consequences, such as implant loosening and vertebral collapse. The role of time-dependant properties of bone is seldom considered. This data could be developed into a constitutive model allowing these time-dependant behaviours to be incorporated in finite element modelling, leading to better predictions of implant loosening, especially for lower quality bone

Statement of purpose: Finite element (FE) models of bone can be used to evaluate new and modified knee replacements. Validation of FE models is seldom used, and the quantification of modelling parameters has a considerable effect on the results obtained. The aim of this study is to develop a FE model of a cadaveric tibia and validate it against a comprehensive set of experiments. Summary of Methods: Seventeen tri-axial rosettes were attached to a cleaned, fresh frozen cadaveric human tibia and the tibia was subjected to 13 loading conditions. Deflection and strain data were used for comparison with the FE model. A geometric model was created on the basis of computed tomography (CT) scans. The CT data was used to map 600 orthotropic material properties to the tibia. All experiments were simulated on the FE model. Measured principal strains were compared to their corresponding FE values using regression analysis. The validated tibia model was reduced in size (75mm to the proximal) and then re-modelled to represent only the proximal tibia. This re-modelled tibia was validated against the reduced size FE model. Virtual surgery was performed on the validated proximal model to implant a UKR. Summary of Results: For the whole tibia model, the regression line for all axial loads combined had a slope of 0.999, an intercept of −6.24 micro-strain, and an R2 value of 0.962. The root mean square error as a percentage was 5%. For the proximal tibia model, correlation coefficients of 0.989 and 0.976 were obtained for the maximum and minimum principal strains respectively. Statement of Conclusions: An FE model of an implanted proximal tibia has been validated against experimental data. This model is able to accurately predict the deflection and stresses in a replaced knee joint to obtain clinically relevant information. This will provide a virtual model of unicompartmental arthroplasty, where variables such as fixation method and bearing mechanics can be assessed

There is an established link between bone quality and fracture risk. It has been suggested that reduced bone quality will also reduce the toughening mechanisms displayed during loading at a high strain rate. We hypothesised that partially decalcified bone will not demonstrate an increase in force required to cause failure when comparing low and high strain rate loading. Mechanical properties were defined by the maximum force at failure. Bone quality was defined by the mineral content. This was altered by subjecting the bones to ultrasonically assisted decalcification in 10M EDTA to achieve an average 18% mineral reduction (A 70 yr old woman has approx 18% of her peak bone mass). 20 pairs of sheep femurs were harvested and split into four equal groups: normal bone quality, fast strain rate (NF); normal bone quality, slow strain rate (NS); low bone quality, fast strain rate (LF) and low bone quality, slow strain rate (LS). All mechanical testing was carried out by means of 3-point bending. Load representing the slow strain rate was applied by a mechanical testing machine (Zwick) at a rate resulting in a deflection of 1mm/s. The dynamic loading was applied by a custom designed pneumatic ram at a mean rate of deflection between the specimens of 2983 mm/s (±SD 1155), this equates to strain rates experienced in a road traffic accident. The following results for force at failure were found (mean ± SD). NF: Force 5503N (± 1012); NS: Force 3969N (± 572); LF: Force 3485N (± 772); LS: Force 3165N (± 605). Groups were compared using a Mann-Whitney U test. Significant results were found between the following groups: Normal bone quality, strain rate compared (NF-NS) p<0.002; Fast strain rate, bone quality compared (NF-LF) p=0.008; Slow strain rate, bone quality compared (NS-LS) p=0.02. No statistical significance was found when comparing low bone quality, strain rate compared (LF-LS) p=0.47. These results show that normal healthy bone has an ability to withstand higher strain rates which protects it against fracture. This ability to withstand high strain rates is lost in decalcified bone making it more susceptible to fracture. The results of this study indicate the importance of strain rate reduction as well as energy absorption in the design of hip protectors and in environmental modifications

The visco-elastic behaviour of cement, is a key feature of cement-implant performance in total hip arthroplasty. The aim of this study was to describe the creep behaviour of the leading plain bone cements under standardised physiological in-vitro conditions. Methods: Cements were mixed under vacuum conditions as per manufacturers instructions. Moulds were used to to produce beams of standard dimensions. These were stored in saline at 37oC for 21 days to ensure thorough polymerisation. Under the same conditions, the beams were tested for 72 hours in a 12-station quasi-static creep rig, using a four-point bending configuration. The rig applied a constant stress of 8MPa to each beam and the deflection was recorded at 8-minute intervals by a data-logging device. The porosity was measured in the mid-cross section of each beam sample using a digital image technique. The cements tested were Palacos R, CMW1 and Smartset GHV and Surgical Simplex P. All data were analysed using ANOVA with Bonfer-roni post-hoc test (SPSS). Results: Palacos R exhibited the highest mean deflection at 72 hours (0.86+/- 0.21mm) followed by Surgical Simplex P (0.85 +/- 0.18mm), CMW1 (0.72 +/- 0.09mm) and Smartset GHV (0.60 +/- 0.16mm). The difference between the two DePuy cements and Palacos R (p=0.03) and Surgical Simplex P (p=0.04) were statistically sig-nificant. None of the beams failed during the test. The creep behaviour correlated with the cross-sectional porosity measurements. Conclusions: This study has shown that there are sig-nificant differences in the creep bahaviour of the leading medium and high viscosity bone cements. In particular Palacos R and Surgical Simplex P demonstrate ‘High’ creep and the DePuy cements ‘Low’ creep. Creep appears sensitive to subtle changes in the composition of the material. This may be reflected in the clinical behaviour of different bone cements and stresses the importance of the time-dependent properties of PMMA